Preface
Today’s ITX cases are either MESH style or all-aluminum alloy, or they are made to the extreme for ITX. Storm Chaser, a manufacturer that has always had breakthrough designs, has brought an eye-catching Transformers-level ITX case this year. , which can be upgraded by three levels based on the ordinary A4 ITX, resulting in S, M, and L forms of the default A4, the top dual-fan A4, and the top 240 integrated water-cooled A4. This is very interesting. The front face uses the most recognizable RGB wireless reflector of Wind Chaser's own water-cooling. The shell is 2.5mm anodized aluminum alloy, which is quite thick in ITX. The internal steel also ensures that the entire For the rigidity of the chassis, the default length, width and height of the S shape are 371x173x211mm, while the M and L are raised 30mm and 60mm respectively, making the heights 211mm, 244mm and 272mm respectively. In terms of volume, they are 13.5L, 15.6L and 17.4 respectively. L. In fact, this is also a good cure for many patients with obsessive-compulsive disorder. The S form can use a low-configuration 72mm CPU air cooling and a three-slot graphics card within 62mm without leaving any open space at the top; the M form can add two additional units to the S form. A 12cm fan is used for top exhaust; while the L shape uses standard 240 water cooling at the top.
This time I am using the largest version of the three-variable model. The main reason is that the configuration is slightly higher and uses a combination of 12700KF + ASUS B660I + 3080ti Metal Master. Therefore, the new M25 white 240 water-cooled by Wind Chaser is used for heat dissipation, and the power supply is used by Wind Chaser itself. The Revolt 750w platinum SFX small power supply, Haiyun OEM's intelligent double protection can easily drive this configuration. The following is the configuration list:
CPU: Intel (Intel) 12th generation Core i7-12700KF processor
motherboard: ROG STRIX B660-I GAMING WIFI motherboard
memory: USCORSAIR 32GB (16G×2) DDR5 5200 Dominion Platinum
graphics card: Galaxy GeForce RTX 3080 Ti Metal Master OC
SSD: Galaxy 1TB SSD solid state drive Hall of Fame HOF EXTREME series
Cooling: PHANTEKS GLACIER ONE Ice Spirit M25 Light and Shadow White 240 all-in-one CPU Water cooling radiator
Power supply: PHANTEKS Revolt 750W SFX Platinum full module small power supply
Chassis: PHANTEKS EVOLV SHIFT Coordinated, with a steel grid panel in the middle, the upper and lower 2.5mm anodized aluminum pieces have the same shape, an angular steel straight man design
In the middle of the front panel is the wireless reflector of the storm chaser, which has the same ID as its own water-cooled Design, the upper aluminum block has a magnetic design, and the power button in the middle of the lower aluminum block can be pushed up by default to expose the interface and RGB switch at the bottom
The right side of the whole machine is 45°, the left and right symmetrical design, the upper and lower symmetrical design, it must be said that it is the same The whole machine has a rigid aesthetic.
Looking down at 45°, the top uses the Wind Chaser M25 240 water cooling. The RGB effect just penetrates the ventilation holes on the top of the case.
The right side panel of the case can be vaguely seen with the Wind Chaser SFX power supply and Corsair. Dominator Platinum Memory and Storm Chaser M25 240 water-cooled
Looking down at 45°
The right side of the matte state
The left side of the matte state, the rear of the 3080TI Metal Master
chassis, the left side of the Asus B660-I motherboard position, the space thickness is 72mm, The thickness of the graphics card space on the right side is 62mm.There is a screw between the motherboard and the power jack at the middle bottom. After unscrewing it, push it forward and you can lift the entire inner tank.
Open the aluminum alloy top cover when the machine is turned on. The Wind Chaser M25 water cooling uses top installation, with the fan at the highest point. , and a water-cooling pipe clamp is used to fix it.
The Wind Chaser M25 240 all-in-one water cooling uses the Wind Chaser's new M25 white RGB fan. The 2000-rpm RGB and air volume and wind pressure mute effects are all balanced
REVOLT SFX power supply and ruler. Platinum D5, M25 240 water-cooled, ASUS B660-I water-cooled
liner status, matte interior right accessory area
liner status, matte 3080TI Metal Master graphics card on the left, and a 2.5 SSD bracket in the lower right corner
Install the matte right side under the 2.5mm anodized aluminum alloy base
Install the matte left graphics card position of the base
Plug in the steel grid panel. The panel is very rigid and you don’t have to worry about deformation. It passes through the front and rear from top to bottom. Insert it by bending, paying attention to the diagonal hook on the front and the flat hook on the back
Insert the grid panel on the right side and see through the rear of the 3080TI Metal Master
chassis. The upper cover has been stacked high. The
shell and liner will be introduced in the chassis unboxing section. Separate, the shell mainly consists of upper and lower aluminum alloy plates , two pieces of aluminum alloy on the front panel, and two left and right grid panels
internal machine, the black and white is also good, the appearance of B660-I is really good, especially the power supply and cooling module, it feels It has a more attractive appearance than the Z690-I
Looking down at the internal unit, the power supply LOGO of the Wind Chaser is also better designed. However, this LOGO is generally not visible on the power supply. On the contrary, the M25 fan is more attractive and the design concept is based on T30 fan
3080TI Metal Master in the internal machine, where the graphics card heats up after , the air is discharged up and down, and the upwind heat is also discharged through the M25 integrated water cooling. Although there is string heat, after all, ITX, why not make good use of the fan exhaust? By the way, the 4P of the M25 fan is designed for serial connection, which is very good, especially if you hate the long wire.
SHIFT The buckle can be stuck and reinforced after the extension cable is inserted into the PCIE slot to prevent it from coming out of the
main accessories area of the machine. The Corsair Ruler platinum memory is still good-looking. The HOF EX solid-state mirror echoes the wireless reflector of the Storm Chaser M25. The power supply of B660I Heat dissipation, no lights, peak appearance
The top cover of the chassis is designed with a rotating shaft. You can lift it by unscrewing the two screws on the opposite side. There is a hole at the rotating shaft to let the water-cooling wire pass down and extend to the inside of the power supply. There is still space inside the power supply. For larger ones, you can put all the extra length of the customized power supply cable into it and organize it a little.
Desktop and lighting display:
Desktop effect of the whole machine
Desktop host lighting
Open the top cover to see the RGB of the M25 water-cooling fan
Split right side Side
Split left graphics card
Host wireless reflector
accessories analysis
Storm Chaser (PHANTEKS) EVOLV SHIFT For a thick graphics card, this ratio is still very small, and the overall 2.5mm anodized aluminum shell is also quite rigid. There is a space between the two aluminum plates on the front face, and the lower plate has a gear that can be lifted up to reveal the front USB at the bottom. and light control buttons. In the middle of the lower panel is the Phanteks logo and the power button
. From the tail design, you can see that the ITX motherboard on the left supports 72mm heat dissipation, and the three-slot graphics card on the right supports 62mm thickness and 147mm height. The thumb screw at the bottom of the middle is used to separate the base and the inner tank. After tightening, the inner tank can be picked up by pushing the inner tank forward. The design is also quite clever.At the same time, the upper and lower aluminum shells have the same folding shape
The aluminum upper cover of the chassis is a three-sided design, and the cut heat dissipation holes are also staggered rectangular
The aluminum lower cover has the same design, and has four relatively wide feet Pad, I personally like such a large foot pad. If the small foot pad is placed on the mouse pad for a long time, it will produce indentations due to gravity.
The left and right sides of the chassis are also of the same design. The front face on the right has a folded corner, which is consistent with the phanteks The design language of our own chassis is the same as
. The upper top cover on the front face has a magnetic design, but it is adsorbed on the top cover because it has to take into account the three-stage height design. To remove the top cover, you need to move the locks on both sides of the infinity reflector toward the middle of the small wave switch
. Take a closer look at the small wave switch on the right. In fact, it is to limit the fixing screw of the chute to prevent the screw from sliding out. I admire the introduction of phanteks This kind of design is so exquisite.
The three-stage design of the completely dismantled family portrait
top cover is through the ingenious design of the front and rear. At the back, as shown in the picture, two plastic fixing pieces are placed to increase the height. That is, the three sections of SML are achieved without placing the fixing piece, the low piece, and the tall piece.
Preface
Today’s ITX cases are either MESH style or all-aluminum alloy, or they are made to the extreme for ITX. Storm Chaser, a manufacturer that has always had breakthrough designs, has brought an eye-catching Transformers-level ITX case this year. , which can be upgraded by three levels based on the ordinary A4 ITX, resulting in S, M, and L forms of the default A4, the top dual-fan A4, and the top 240 integrated water-cooled A4. This is very interesting. The front face uses the most recognizable RGB wireless reflector of Wind Chaser's own water-cooling. The shell is 2.5mm anodized aluminum alloy, which is quite thick in ITX. The internal steel also ensures that the entire For the rigidity of the chassis, the default length, width and height of the S shape are 371x173x211mm, while the M and L are raised 30mm and 60mm respectively, making the heights 211mm, 244mm and 272mm respectively. In terms of volume, they are 13.5L, 15.6L and 17.4 respectively. L. In fact, this is also a good cure for many patients with obsessive-compulsive disorder. The S form can use a low-configuration 72mm CPU air cooling and a three-slot graphics card within 62mm without leaving any open space at the top; the M form can add two additional units to the S form. A 12cm fan is used for top exhaust; while the L shape uses standard 240 water cooling at the top.
This time I am using the largest version of the three-variable model. The main reason is that the configuration is slightly higher and uses a combination of 12700KF + ASUS B660I + 3080ti Metal Master. Therefore, the new M25 white 240 water-cooled by Wind Chaser is used for heat dissipation, and the power supply is used by Wind Chaser itself. The Revolt 750w platinum SFX small power supply, Haiyun OEM's intelligent double protection can easily drive this configuration. The following is the configuration list:
CPU: Intel (Intel) 12th generation Core i7-12700KF processor
motherboard: ROG STRIX B660-I GAMING WIFI motherboard
memory: USCORSAIR 32GB (16G×2) DDR5 5200 Dominion Platinum
graphics card: Galaxy GeForce RTX 3080 Ti Metal Master OC
SSD: Galaxy 1TB SSD solid state drive Hall of Fame HOF EXTREME series
Cooling: PHANTEKS GLACIER ONE Ice Spirit M25 Light and Shadow White 240 all-in-one CPU Water cooling radiator
Power supply: PHANTEKS Revolt 750W SFX Platinum full module small power supply
Chassis: PHANTEKS EVOLV SHIFT Coordinated, with a steel grid panel in the middle, the upper and lower 2.5mm anodized aluminum pieces have the same shape, an angular steel straight man design
In the middle of the front panel is the wireless reflector of the storm chaser, which has the same ID as its own water-cooled Design, the upper aluminum block has a magnetic design, and the power button in the middle of the lower aluminum block can be pushed up by default to expose the interface and RGB switch at the bottom
The right side of the whole machine is 45°, the left and right symmetrical design, the upper and lower symmetrical design, it must be said that it is the same The whole machine has a rigid aesthetic.
Looking down at 45°, the top uses the Wind Chaser M25 240 water cooling. The RGB effect just penetrates the ventilation holes on the top of the case.
The right side panel of the case can be vaguely seen with the Wind Chaser SFX power supply and Corsair. Dominator Platinum Memory and Storm Chaser M25 240 water-cooled
Looking down at 45°
The right side of the matte state
The left side of the matte state, the rear of the 3080TI Metal Master
chassis, the left side of the Asus B660-I motherboard position, the space thickness is 72mm, The thickness of the graphics card space on the right side is 62mm.There is a screw between the motherboard and the power jack at the middle bottom. After unscrewing it, push it forward and you can lift the entire inner tank.
Open the aluminum alloy top cover when the machine is turned on. The Wind Chaser M25 water cooling uses top installation, with the fan at the highest point. , and a water-cooling pipe clamp is used to fix it.
The Wind Chaser M25 240 all-in-one water cooling uses the Wind Chaser's new M25 white RGB fan. The 2000-rpm RGB and air volume and wind pressure mute effects are all balanced
REVOLT SFX power supply and ruler. Platinum D5, M25 240 water-cooled, ASUS B660-I water-cooled
liner status, matte interior right accessory area
liner status, matte 3080TI Metal Master graphics card on the left, and a 2.5 SSD bracket in the lower right corner
Install the matte right side under the 2.5mm anodized aluminum alloy base
Install the matte left graphics card position of the base
Plug in the steel grid panel. The panel is very rigid and you don’t have to worry about deformation. It passes through the front and rear from top to bottom. Insert it by bending, paying attention to the diagonal hook on the front and the flat hook on the back
Insert the grid panel on the right side and see through the rear of the 3080TI Metal Master
chassis. The upper cover has been stacked high. The
shell and liner will be introduced in the chassis unboxing section. Separate, the shell mainly consists of upper and lower aluminum alloy plates , two pieces of aluminum alloy on the front panel, and two left and right grid panels
internal machine, the black and white is also good, the appearance of B660-I is really good, especially the power supply and cooling module, it feels It has a more attractive appearance than the Z690-I
Looking down at the internal unit, the power supply LOGO of the Wind Chaser is also better designed. However, this LOGO is generally not visible on the power supply. On the contrary, the M25 fan is more attractive and the design concept is based on T30 fan
3080TI Metal Master in the internal machine, where the graphics card heats up after , the air is discharged up and down, and the upwind heat is also discharged through the M25 integrated water cooling. Although there is string heat, after all, ITX, why not make good use of the fan exhaust? By the way, the 4P of the M25 fan is designed for serial connection, which is very good, especially if you hate the long wire.
SHIFT The buckle can be stuck and reinforced after the extension cable is inserted into the PCIE slot to prevent it from coming out of the
main accessories area of the machine. The Corsair Ruler platinum memory is still good-looking. The HOF EX solid-state mirror echoes the wireless reflector of the Storm Chaser M25. The power supply of B660I Heat dissipation, no lights, peak appearance
The top cover of the chassis is designed with a rotating shaft. You can lift it by unscrewing the two screws on the opposite side. There is a hole at the rotating shaft to let the water-cooling wire pass down and extend to the inside of the power supply. There is still space inside the power supply. For larger ones, you can put all the extra length of the customized power supply cable into it and organize it a little.
Desktop and lighting display:
Desktop effect of the whole machine
Desktop host lighting
Open the top cover to see the RGB of the M25 water-cooling fan
Split right side Side
Split left graphics card
Host wireless reflector
accessories analysis
Storm Chaser (PHANTEKS) EVOLV SHIFT For a thick graphics card, this ratio is still very small, and the overall 2.5mm anodized aluminum shell is also quite rigid. There is a space between the two aluminum plates on the front face, and the lower plate has a gear that can be lifted up to reveal the front USB at the bottom. and light control buttons. In the middle of the lower panel is the Phanteks logo and the power button
. From the tail design, you can see that the ITX motherboard on the left supports 72mm heat dissipation, and the three-slot graphics card on the right supports 62mm thickness and 147mm height. The thumb screw at the bottom of the middle is used to separate the base and the inner tank. After tightening, the inner tank can be picked up by pushing the inner tank forward. The design is also quite clever.At the same time, the upper and lower aluminum shells have the same folding shape
The aluminum upper cover of the chassis is a three-sided design, and the cut heat dissipation holes are also staggered rectangular
The aluminum lower cover has the same design, and has four relatively wide feet Pad, I personally like such a large foot pad. If the small foot pad is placed on the mouse pad for a long time, it will produce indentations due to gravity.
The left and right sides of the chassis are also of the same design. The front face on the right has a folded corner, which is consistent with the phanteks The design language of our own chassis is the same as
. The upper top cover on the front face has a magnetic design, but it is adsorbed on the top cover because it has to take into account the three-stage height design. To remove the top cover, you need to move the locks on both sides of the infinity reflector toward the middle of the small wave switch
. Take a closer look at the small wave switch on the right. In fact, it is to limit the fixing screw of the chute to prevent the screw from sliding out. I admire the introduction of phanteks This kind of design is so exquisite.
The three-stage design of the completely dismantled family portrait
top cover is through the ingenious design of the front and rear. At the back, as shown in the picture, two plastic fixing pieces are placed to increase the height. That is, the three sections of SML are achieved without placing the fixing piece, the low piece, and the tall piece.It should be noted here that the two screws of the plastic part must be screwed on, otherwise taking the top cover of the chassis will cause the rear part to come out.
In the front, the screw that can move up, middle and down is blocked by the fluctuation switch on the front panel to achieve the three levels of LMS. Segment height
Three-segment side profile, which proportion do you prefer?
Which proportion of the three-section front panel do you prefer? What's more, it has an infinite reflector designed inside, and its RGB is also designed with vertical stripes.
has a three-section tail. Which ratio do you like better? The left side is air-cooled, and the middle top is raised 3cm to fit two 12CMs, and the right side is raised 6CM to fit the integrated water-cooling
The top cover of the inner tank needs to be installed with water cooling and ducting, so an upward-turning hinge is also designed
The left side of the inner tank On the side, there is a dent in the middle partition of the front SFX power supply, which is used to supply power to the graphics card. On the right side of the motherboard, there is a standard PCIE4.0 extension cable of Storm Chaser, which is quite strong.
liner The right side of the graphics card slot is also designed on the right side. A 2.5 SSD slot is provided for emergencies. There are two foot pads on the graphics card back to the power supply to prevent the wind from the rear of the 30 graphics card from suffocating the front bottom of the
liner. The power extension cable and front IO are both there. The fixed design here makes it easier to route cables.
There are threading holes at the top and front of the cold row at the top of the liner. There are also two holes for the water cooling pipe on one side of the motherboard. The two hinges at the end can also be opened. Take it off, there are two fixing screws on the front
Republic of Gamers ROG STRIX B660-I GAMING WIFI motherboard
ITX. The choice is B660 for the 12th generation. Overclocking is a bit overwhelming and the default is fine. I have to say that for Z690-I and B660-I I still think this is the B660-I of ASUS , which looks better.
The back of the red and black packaging style shows the parameters and features of the product. The 8+1 DIGI+ digital power supply configuration is sufficient by default.
The motherboard has a standard ITX all-black design. The new design language, the slash-cut power supply and heat dissipation are full of texture, STRIX and small eyes are still very cute, although ITX still provides a metal-reinforced PCIE5.0 slot
8 The back of the PCB is also covered with various Parts, there is also an m.2 slot and the m.2 on the chipset heat dissipation provides a total of two 4.0 high-intensity power supplies that support
8PIN. The fan provides three interfaces: CPU, PUMP, and SYS. ARGB also has 12V and 5V; ASUS AEMP memory technology can unlock DDR5 memory PMIC limit up to 6200+. ITX memory overclocking capability is still very strong
. The back IO is designed with ROG small eyes. The interfaces are integrated display HDMI and DP, three USB2.0, three USB3.0, wired
Storm Chaser GLACIER ONE Ice Spirit M25 Light and Shadow White 240 integrated water cooling
A new model named after the M25 fan GLACIER ONE is a new generation of all-in-one water cooling. In fact, GLACIER ONE’s current F120MP is also my favorite fan. It has balanced parameters and is more cost-effective. The new M25 fan also uses last year’s heavyweight T30 fan as its design language; the new water-cooled turquoise color The packaging is also artistic.
GLACIER ONE 360 M25 is an all-in-one water-cooled family portrait, covering all platforms buckles on sale, and includes 3 thoughtfully designed water-cooled pipe clamps
The water-cooled body is very well made, and the heat exchange efficiency of the single-wave design aluminum row is It is high and does not require much fan, with a conventional thickness of 27mm and 12 micro-water channels. The right end of the cold radiator is a maintenance port and two water inlets and inlets
. The improved design of this water cooling is to design the water pump at the axis in the middle of the 12CM fan position. Therefore, the design here will not affect the blowing effect of the fan. The water pump power supply line can be installed by pressing down from the cuts at both ends without affecting the installation of the fan.
The side of the cold radiator has the PHANTEKS LOGO
The cold head cover is still the original infinite mirror cooling The head cover has a magnetic suction design and is integrated with the cold head. However, the cold head is very small because it does not have a water pump.
The cold head is pre-coated with silicone grease and is equipped with a tube of silicone grease. There is a 0.1mm micro water channel inside; the design is under the cold head cover. Two magnetic suction and ARGB cables
Wind Chaser M25 series fans continue the design concept of T30, using nine fan blades and large hydraulic bearings. It can provide air volume of 84.26CFM, wind pressure of 2.67mmH2O at 2000RPM, PWM FAN cable and ARGB The lines are all designed in series
The infinite mirror cooling head cover is integrated with the water cooling and M25 fans. There is also PHANTEKS's LOGO on the side of the cooling radiator
GALAXY GeForce RTX 3080 Ti Metal Master OC
The graphics card chose the RTX3080TI Metal Master OC of GALAXY , equipped with the GA102-225 core , the number of CUDA processors reaches 10,240, equipped with 12GB, 384 bit, 19Gbps GDDR6X video memory.The body of the graphics card has a pure metal upper cover. The radiator is die-cast and stamped in one piece. The size is 318x107x60mm. Although there are some irregular lines and triangular openings, the overall design is still rectangular within three slots.
public version The dual 8P power supply design of the 12-layer PCB has a TGP of 350W; the side of the radiator upper cover has the GALAX LOGO and the GEFORCE RTX NVIDIA model logo, and there are flat ventilation holes on the shoulders of the upper cover. Enhance heat dissipation. In fact, this is also a design derivative of 3090RTX FE. The short PCB increases heat dissipation for the third fan. The accessory provides a double-slot baffle for replacement, and the interface is a standard 3DP1.4A+1HDMI2.1 design.
PHANTEKS Revolt 750W SFX platinum full module small power supply
PHANTEKS REVOLT SFX 750W, as a The platinum SFX power supply that was renewed in 2010 uses the complete version of Haiyun SPX-750. It is indeed the price of the youth version, and it has to be said that the price-performance ratio is excellent. The packaging is still the simple black color of the storm chaser, with the LOGO on the upper left and the model number
on the back of the package. The characteristics of the power supply include the module line, size parameters, 80PLUS certification, and the 92MMFDB hydraulic fan and fan stall speed curve. Of course, the most eye-catching one is 10YEARS. WARRANTY got a family portrait of the
power supply. The power supply comes with an SFX2ATX adapter board in case of emergency. The flat module cable that comes with it is neither soft nor hard. It can be installed at a long length, which is of course the best choice for safety and stability. The size of the
power supply is 100x63. Standard short body SFX design of 5x125mm.The air inlet has a honeycomb shape. The 92mm FDB fan stops at 40% load by default. The power supply nameplate details the parameters of
, which is relatively quiet. As a small steel cannon power supply, the performance cannot be weak. It has all Japanese capacitors and OPP/OVP/UVP/OCP/OTP. /SCP six-layer protection certification, 93.5% ultra-platinum conversion efficiency, SMD solder paste process, direct plug-in wire-free connection technology, and of course Haiyun’s SDP intelligent dual protection to cope with complex short-term 120% and 135% Instantaneous overload protection
power supply full module interface design, white and gray PHANTEKS REVOLT SFX embellishment, module interface definition of each interface partition, including four groups of CPU/PCIe designs, to cope with the extreme interface requirements of dual CPU + three GPUs, You need to use a 1 to 2 graphics card cable, but in general ITX, a single 8CPU + three GPUs is the limit.
The side of the power supply still has the white PHANTEKS logo and the gray REVOLT SFX model logo
. Only the power interface and switch are designed on the back of the power supply, and the rest are It is an air vent design, with a small power supply and ventilation and heat dissipation.
USCORSAIR 32GB (16G×2) DDR5 5200 Dominator Platinum
The memory used is the USCORSAIR Dominator Platinum DDR5 5200 32G (16GX2) set, color The value and basic performance are all there, and the heat dissipation design of the Dominator Platinum should be the thickest design at present. The aluminum alloy shape with
DHX heat dissipation technology is simple and stable, and matches the RGB effect of CAPELLIX LED technology of Corsair , with the Corsair in the middle. LOGO and DOMINATOR PLATINUM RGB
There are RGB light guide areas on the top and sides of the memory. Each memory contains 12 independently addressable high-brightness CAPLLIX LEDs
. The cutting angles on both ends of the memory are exactly 45 degrees, and there is DDR5 / DHX (heat dissipation technology) in the upper right corner. Logo), containing all of CORSAIR's top designs for memory
Hall of Fame HOF EXTREME series PCIE 4.0 SSD
solid state drive adopts Hall of Fame HOF EXTREME series SSD, which is the latest eight-channel Phison E18 master, with sequential read and write capabilities up to 7000 /5500MB/S speed
SSD body is a silver ice mirror radiator, still using the HOF Hall of Fame white PCB
The back is a warranty label, providing a 5-year 700TBW limited warranty, while the 2TB model provides 1400TBW
Complete machine test
Test CPUZ The single-core score is 788.3 points, and the multi-core score is 9316.8 points. With the participation of small cores, the 12th generation single-core and multi-core are both relatively powerful combinations.
CineBench R23 test scores are 1845 for single core and 22364 for multi-core. 2
CineBench R20 test scores are 711 for single core and 8559 for multi-core R15 test results Single-core 270, multi-core 3317
Corsair Dominator Platinum DDR5 5200’s XMP results, read, write and copy performance have reached 78G\73G\71GMB/S speed. Although the delay is slightly higher, the performance is here after all. DDR5 is also a trend.
PCMARK10 test Office application and digital content creation score 8836
Master Lu test The overall machine performance is more than 2.36 million points
GALAXY 3080TI Metal Master OC's GPU-Z
Single baked FPU test, the room temperature is about 26 degrees, the 12700KF display power consumption is about 200W, the CPU temperature It is basically around 90 degrees. The performance of the Wind Chaser M25 240 integrated water cooling on the 12th generation 12700KF is still very good.
The core of the donut roaster reaches 74° in 10 minutes. The power consumption of the graphics card is around 360W. The power consumption and heat generation are still the same. Proportional
3D MARK TIME SPY EXTREME test score 9402
3D MARK TIME SPY test score 18964
3D MARK PORT ROYAL ray tracing test score 12897
3D MARK FIRE STRIKE ULTRA test score 125 71
3D MARK FIRE STRIKE EXTREME test score 22884
3D MARK FIRE STRIKE test score 34500
Tomb Raider · Shadow tested at 4K resolution with DLSS turned on and the highest ray tracing an average of 81FPS
Gears of War 5 tested at 4K resolution with ultra-high special effects and averaged 78.7FPS The average test under the highest extreme special effects is 85FPS
. The above is the entire content of this installation. Everyone is welcome to share and exchange. Thank you for reading
The body of the graphics card has a pure metal upper cover. The radiator is die-cast and stamped in one piece. The size is 318x107x60mm. Although there are some irregular lines and triangular openings, the overall design is still rectangular within three slots.
public version The dual 8P power supply design of the 12-layer PCB has a TGP of 350W; the side of the radiator upper cover has the GALAX LOGO and the GEFORCE RTX NVIDIA model logo, and there are flat ventilation holes on the shoulders of the upper cover. Enhance heat dissipation. In fact, this is also a design derivative of 3090RTX FE. The short PCB increases heat dissipation for the third fan. The accessory provides a double-slot baffle for replacement, and the interface is a standard 3DP1.4A+1HDMI2.1 design.
PHANTEKS Revolt 750W SFX platinum full module small power supply
PHANTEKS REVOLT SFX 750W, as a The platinum SFX power supply that was renewed in 2010 uses the complete version of Haiyun SPX-750. It is indeed the price of the youth version, and it has to be said that the price-performance ratio is excellent. The packaging is still the simple black color of the storm chaser, with the LOGO on the upper left and the model number
on the back of the package. The characteristics of the power supply include the module line, size parameters, 80PLUS certification, and the 92MMFDB hydraulic fan and fan stall speed curve. Of course, the most eye-catching one is 10YEARS. WARRANTY got a family portrait of the
power supply. The power supply comes with an SFX2ATX adapter board in case of emergency. The flat module cable that comes with it is neither soft nor hard. It can be installed at a long length, which is of course the best choice for safety and stability. The size of the
power supply is 100x63. Standard short body SFX design of 5x125mm.
Preface
Today’s ITX cases are either MESH style or all-aluminum alloy, or they are made to the extreme for ITX. Storm Chaser, a manufacturer that has always had breakthrough designs, has brought an eye-catching Transformers-level ITX case this year. , which can be upgraded by three levels based on the ordinary A4 ITX, resulting in S, M, and L forms of the default A4, the top dual-fan A4, and the top 240 integrated water-cooled A4. This is very interesting. The front face uses the most recognizable RGB wireless reflector of Wind Chaser's own water-cooling. The shell is 2.5mm anodized aluminum alloy, which is quite thick in ITX. The internal steel also ensures that the entire For the rigidity of the chassis, the default length, width and height of the S shape are 371x173x211mm, while the M and L are raised 30mm and 60mm respectively, making the heights 211mm, 244mm and 272mm respectively. In terms of volume, they are 13.5L, 15.6L and 17.4 respectively. L. In fact, this is also a good cure for many patients with obsessive-compulsive disorder. The S form can use a low-configuration 72mm CPU air cooling and a three-slot graphics card within 62mm without leaving any open space at the top; the M form can add two additional units to the S form. A 12cm fan is used for top exhaust; while the L shape uses standard 240 water cooling at the top.
This time I am using the largest version of the three-variable model. The main reason is that the configuration is slightly higher and uses a combination of 12700KF + ASUS B660I + 3080ti Metal Master. Therefore, the new M25 white 240 water-cooled by Wind Chaser is used for heat dissipation, and the power supply is used by Wind Chaser itself. The Revolt 750w platinum SFX small power supply, Haiyun OEM's intelligent double protection can easily drive this configuration. The following is the configuration list:
CPU: Intel (Intel) 12th generation Core i7-12700KF processor
motherboard: ROG STRIX B660-I GAMING WIFI motherboard
memory: USCORSAIR 32GB (16G×2) DDR5 5200 Dominion Platinum
graphics card: Galaxy GeForce RTX 3080 Ti Metal Master OC
SSD: Galaxy 1TB SSD solid state drive Hall of Fame HOF EXTREME series
Cooling: PHANTEKS GLACIER ONE Ice Spirit M25 Light and Shadow White 240 all-in-one CPU Water cooling radiator
Power supply: PHANTEKS Revolt 750W SFX Platinum full module small power supply
Chassis: PHANTEKS EVOLV SHIFT Coordinated, with a steel grid panel in the middle, the upper and lower 2.5mm anodized aluminum pieces have the same shape, an angular steel straight man design
In the middle of the front panel is the wireless reflector of the storm chaser, which has the same ID as its own water-cooled Design, the upper aluminum block has a magnetic design, and the power button in the middle of the lower aluminum block can be pushed up by default to expose the interface and RGB switch at the bottom
The right side of the whole machine is 45°, the left and right symmetrical design, the upper and lower symmetrical design, it must be said that it is the same The whole machine has a rigid aesthetic.
Looking down at 45°, the top uses the Wind Chaser M25 240 water cooling. The RGB effect just penetrates the ventilation holes on the top of the case.
The right side panel of the case can be vaguely seen with the Wind Chaser SFX power supply and Corsair. Dominator Platinum Memory and Storm Chaser M25 240 water-cooled
Looking down at 45°
The right side of the matte state
The left side of the matte state, the rear of the 3080TI Metal Master
chassis, the left side of the Asus B660-I motherboard position, the space thickness is 72mm, The thickness of the graphics card space on the right side is 62mm.There is a screw between the motherboard and the power jack at the middle bottom. After unscrewing it, push it forward and you can lift the entire inner tank.
Open the aluminum alloy top cover when the machine is turned on. The Wind Chaser M25 water cooling uses top installation, with the fan at the highest point. , and a water-cooling pipe clamp is used to fix it.
The Wind Chaser M25 240 all-in-one water cooling uses the Wind Chaser's new M25 white RGB fan. The 2000-rpm RGB and air volume and wind pressure mute effects are all balanced
REVOLT SFX power supply and ruler. Platinum D5, M25 240 water-cooled, ASUS B660-I water-cooled
liner status, matte interior right accessory area
liner status, matte 3080TI Metal Master graphics card on the left, and a 2.5 SSD bracket in the lower right corner
Install the matte right side under the 2.5mm anodized aluminum alloy base
Install the matte left graphics card position of the base
Plug in the steel grid panel. The panel is very rigid and you don’t have to worry about deformation. It passes through the front and rear from top to bottom. Insert it by bending, paying attention to the diagonal hook on the front and the flat hook on the back
Insert the grid panel on the right side and see through the rear of the 3080TI Metal Master
chassis. The upper cover has been stacked high. The
shell and liner will be introduced in the chassis unboxing section. Separate, the shell mainly consists of upper and lower aluminum alloy plates , two pieces of aluminum alloy on the front panel, and two left and right grid panels
internal machine, the black and white is also good, the appearance of B660-I is really good, especially the power supply and cooling module, it feels It has a more attractive appearance than the Z690-I
Looking down at the internal unit, the power supply LOGO of the Wind Chaser is also better designed. However, this LOGO is generally not visible on the power supply. On the contrary, the M25 fan is more attractive and the design concept is based on T30 fan
3080TI Metal Master in the internal machine, where the graphics card heats up after , the air is discharged up and down, and the upwind heat is also discharged through the M25 integrated water cooling. Although there is string heat, after all, ITX, why not make good use of the fan exhaust? By the way, the 4P of the M25 fan is designed for serial connection, which is very good, especially if you hate the long wire.
SHIFT The buckle can be stuck and reinforced after the extension cable is inserted into the PCIE slot to prevent it from coming out of the
main accessories area of the machine. The Corsair Ruler platinum memory is still good-looking. The HOF EX solid-state mirror echoes the wireless reflector of the Storm Chaser M25. The power supply of B660I Heat dissipation, no lights, peak appearance
The top cover of the chassis is designed with a rotating shaft. You can lift it by unscrewing the two screws on the opposite side. There is a hole at the rotating shaft to let the water-cooling wire pass down and extend to the inside of the power supply. There is still space inside the power supply. For larger ones, you can put all the extra length of the customized power supply cable into it and organize it a little.
Desktop and lighting display:
Desktop effect of the whole machine
Desktop host lighting
Open the top cover to see the RGB of the M25 water-cooling fan
Split right side Side
Split left graphics card
Host wireless reflector
accessories analysis
Storm Chaser (PHANTEKS) EVOLV SHIFT For a thick graphics card, this ratio is still very small, and the overall 2.5mm anodized aluminum shell is also quite rigid. There is a space between the two aluminum plates on the front face, and the lower plate has a gear that can be lifted up to reveal the front USB at the bottom. and light control buttons. In the middle of the lower panel is the Phanteks logo and the power button
. From the tail design, you can see that the ITX motherboard on the left supports 72mm heat dissipation, and the three-slot graphics card on the right supports 62mm thickness and 147mm height. The thumb screw at the bottom of the middle is used to separate the base and the inner tank. After tightening, the inner tank can be picked up by pushing the inner tank forward. The design is also quite clever.At the same time, the upper and lower aluminum shells have the same folding shape
The aluminum upper cover of the chassis is a three-sided design, and the cut heat dissipation holes are also staggered rectangular
The aluminum lower cover has the same design, and has four relatively wide feet Pad, I personally like such a large foot pad. If the small foot pad is placed on the mouse pad for a long time, it will produce indentations due to gravity.
The left and right sides of the chassis are also of the same design. The front face on the right has a folded corner, which is consistent with the phanteks The design language of our own chassis is the same as
. The upper top cover on the front face has a magnetic design, but it is adsorbed on the top cover because it has to take into account the three-stage height design. To remove the top cover, you need to move the locks on both sides of the infinity reflector toward the middle of the small wave switch
. Take a closer look at the small wave switch on the right. In fact, it is to limit the fixing screw of the chute to prevent the screw from sliding out. I admire the introduction of phanteks This kind of design is so exquisite.
The three-stage design of the completely dismantled family portrait
top cover is through the ingenious design of the front and rear. At the back, as shown in the picture, two plastic fixing pieces are placed to increase the height. That is, the three sections of SML are achieved without placing the fixing piece, the low piece, and the tall piece.It should be noted here that the two screws of the plastic part must be screwed on, otherwise taking the top cover of the chassis will cause the rear part to come out.
In the front, the screw that can move up, middle and down is blocked by the fluctuation switch on the front panel to achieve the three levels of LMS. Segment height
Three-segment side profile, which proportion do you prefer?
Which proportion of the three-section front panel do you prefer? What's more, it has an infinite reflector designed inside, and its RGB is also designed with vertical stripes.
has a three-section tail. Which ratio do you like better? The left side is air-cooled, and the middle top is raised 3cm to fit two 12CMs, and the right side is raised 6CM to fit the integrated water-cooling
The top cover of the inner tank needs to be installed with water cooling and ducting, so an upward-turning hinge is also designed
The left side of the inner tank On the side, there is a dent in the middle partition of the front SFX power supply, which is used to supply power to the graphics card. On the right side of the motherboard, there is a standard PCIE4.0 extension cable of Storm Chaser, which is quite strong.
liner The right side of the graphics card slot is also designed on the right side. A 2.5 SSD slot is provided for emergencies. There are two foot pads on the graphics card back to the power supply to prevent the wind from the rear of the 30 graphics card from suffocating the front bottom of the
liner. The power extension cable and front IO are both there. The fixed design here makes it easier to route cables.
There are threading holes at the top and front of the cold row at the top of the liner. There are also two holes for the water cooling pipe on one side of the motherboard. The two hinges at the end can also be opened. Take it off, there are two fixing screws on the front
Republic of Gamers ROG STRIX B660-I GAMING WIFI motherboard
ITX. The choice is B660 for the 12th generation. Overclocking is a bit overwhelming and the default is fine. I have to say that for Z690-I and B660-I I still think this is the B660-I of ASUS , which looks better.
The back of the red and black packaging style shows the parameters and features of the product. The 8+1 DIGI+ digital power supply configuration is sufficient by default.
The motherboard has a standard ITX all-black design. The new design language, the slash-cut power supply and heat dissipation are full of texture, STRIX and small eyes are still very cute, although ITX still provides a metal-reinforced PCIE5.0 slot
8 The back of the PCB is also covered with various Parts, there is also an m.2 slot and the m.2 on the chipset heat dissipation provides a total of two 4.0 high-intensity power supplies that support
8PIN. The fan provides three interfaces: CPU, PUMP, and SYS. ARGB also has 12V and 5V; ASUS AEMP memory technology can unlock DDR5 memory PMIC limit up to 6200+. ITX memory overclocking capability is still very strong
. The back IO is designed with ROG small eyes. The interfaces are integrated display HDMI and DP, three USB2.0, three USB3.0, wired
Storm Chaser GLACIER ONE Ice Spirit M25 Light and Shadow White 240 integrated water cooling
A new model named after the M25 fan GLACIER ONE is a new generation of all-in-one water cooling. In fact, GLACIER ONE’s current F120MP is also my favorite fan. It has balanced parameters and is more cost-effective. The new M25 fan also uses last year’s heavyweight T30 fan as its design language; the new water-cooled turquoise color The packaging is also artistic.
GLACIER ONE 360 M25 is an all-in-one water-cooled family portrait, covering all platforms buckles on sale, and includes 3 thoughtfully designed water-cooled pipe clamps
The water-cooled body is very well made, and the heat exchange efficiency of the single-wave design aluminum row is It is high and does not require much fan, with a conventional thickness of 27mm and 12 micro-water channels. The right end of the cold radiator is a maintenance port and two water inlets and inlets
. The improved design of this water cooling is to design the water pump at the axis in the middle of the 12CM fan position. Therefore, the design here will not affect the blowing effect of the fan. The water pump power supply line can be installed by pressing down from the cuts at both ends without affecting the installation of the fan.
The side of the cold radiator has the PHANTEKS LOGO
The cold head cover is still the original infinite mirror cooling The head cover has a magnetic suction design and is integrated with the cold head. However, the cold head is very small because it does not have a water pump.
The cold head is pre-coated with silicone grease and is equipped with a tube of silicone grease. There is a 0.1mm micro water channel inside; the design is under the cold head cover. Two magnetic suction and ARGB cables
Wind Chaser M25 series fans continue the design concept of T30, using nine fan blades and large hydraulic bearings. It can provide air volume of 84.26CFM, wind pressure of 2.67mmH2O at 2000RPM, PWM FAN cable and ARGB The lines are all designed in series
The infinite mirror cooling head cover is integrated with the water cooling and M25 fans. There is also PHANTEKS's LOGO on the side of the cooling radiator
GALAXY GeForce RTX 3080 Ti Metal Master OC
The graphics card chose the RTX3080TI Metal Master OC of GALAXY , equipped with the GA102-225 core , the number of CUDA processors reaches 10,240, equipped with 12GB, 384 bit, 19Gbps GDDR6X video memory.The body of the graphics card has a pure metal upper cover. The radiator is die-cast and stamped in one piece. The size is 318x107x60mm. Although there are some irregular lines and triangular openings, the overall design is still rectangular within three slots.
public version The dual 8P power supply design of the 12-layer PCB has a TGP of 350W; the side of the radiator upper cover has the GALAX LOGO and the GEFORCE RTX NVIDIA model logo, and there are flat ventilation holes on the shoulders of the upper cover. Enhance heat dissipation. In fact, this is also a design derivative of 3090RTX FE. The short PCB increases heat dissipation for the third fan. The accessory provides a double-slot baffle for replacement, and the interface is a standard 3DP1.4A+1HDMI2.1 design.
PHANTEKS Revolt 750W SFX platinum full module small power supply
PHANTEKS REVOLT SFX 750W, as a The platinum SFX power supply that was renewed in 2010 uses the complete version of Haiyun SPX-750. It is indeed the price of the youth version, and it has to be said that the price-performance ratio is excellent. The packaging is still the simple black color of the storm chaser, with the LOGO on the upper left and the model number
on the back of the package. The characteristics of the power supply include the module line, size parameters, 80PLUS certification, and the 92MMFDB hydraulic fan and fan stall speed curve. Of course, the most eye-catching one is 10YEARS. WARRANTY got a family portrait of the
power supply. The power supply comes with an SFX2ATX adapter board in case of emergency. The flat module cable that comes with it is neither soft nor hard. It can be installed at a long length, which is of course the best choice for safety and stability. The size of the
power supply is 100x63. Standard short body SFX design of 5x125mm.The air inlet has a honeycomb shape. The 92mm FDB fan stops at 40% load by default. The power supply nameplate details the parameters of
, which is relatively quiet. As a small steel cannon power supply, the performance cannot be weak. It has all Japanese capacitors and OPP/OVP/UVP/OCP/OTP. /SCP six-layer protection certification, 93.5% ultra-platinum conversion efficiency, SMD solder paste process, direct plug-in wire-free connection technology, and of course Haiyun’s SDP intelligent dual protection to cope with complex short-term 120% and 135% Instantaneous overload protection
power supply full module interface design, white and gray PHANTEKS REVOLT SFX embellishment, module interface definition of each interface partition, including four groups of CPU/PCIe designs, to cope with the extreme interface requirements of dual CPU + three GPUs, You need to use a 1 to 2 graphics card cable, but in general ITX, a single 8CPU + three GPUs is the limit.
The side of the power supply still has the white PHANTEKS logo and the gray REVOLT SFX model logo
. Only the power interface and switch are designed on the back of the power supply, and the rest are It is an air vent design, with a small power supply and ventilation and heat dissipation.
USCORSAIR 32GB (16G×2) DDR5 5200 Dominator Platinum
The memory used is the USCORSAIR Dominator Platinum DDR5 5200 32G (16GX2) set, color The value and basic performance are all there, and the heat dissipation design of the Dominator Platinum should be the thickest design at present. The aluminum alloy shape with
DHX heat dissipation technology is simple and stable, and matches the RGB effect of CAPELLIX LED technology of Corsair , with the Corsair in the middle. LOGO and DOMINATOR PLATINUM RGB
There are RGB light guide areas on the top and sides of the memory. Each memory contains 12 independently addressable high-brightness CAPLLIX LEDs
. The cutting angles on both ends of the memory are exactly 45 degrees, and there is DDR5 / DHX (heat dissipation technology) in the upper right corner. Logo), containing all of CORSAIR's top designs for memory
Hall of Fame HOF EXTREME series PCIE 4.0 SSD
solid state drive adopts Hall of Fame HOF EXTREME series SSD, which is the latest eight-channel Phison E18 master, with sequential read and write capabilities up to 7000 /5500MB/S speed
SSD body is a silver ice mirror radiator, still using the HOF Hall of Fame white PCB
The back is a warranty label, providing a 5-year 700TBW limited warranty, while the 2TB model provides 1400TBW
Complete machine test
Test CPUZ The single-core score is 788.3 points, and the multi-core score is 9316.8 points. With the participation of small cores, the 12th generation single-core and multi-core are both relatively powerful combinations.
CineBench R23 test scores are 1845 for single core and 22364 for multi-core. 2
CineBench R20 test scores are 711 for single core and 8559 for multi-core R15 test results Single-core 270, multi-core 3317
Corsair Dominator Platinum DDR5 5200’s XMP results, read, write and copy performance have reached 78G\73G\71GMB/S speed. Although the delay is slightly higher, the performance is here after all. DDR5 is also a trend.
PCMARK10 test Office application and digital content creation score 8836
Master Lu test The overall machine performance is more than 2.36 million points
GALAXY 3080TI Metal Master OC's GPU-Z
Single baked FPU test, the room temperature is about 26 degrees, the 12700KF display power consumption is about 200W, the CPU temperature It is basically around 90 degrees. The performance of the Wind Chaser M25 240 integrated water cooling on the 12th generation 12700KF is still very good.
The core of the donut roaster reaches 74° in 10 minutes. The power consumption of the graphics card is around 360W. The power consumption and heat generation are still the same. Proportional
3D MARK TIME SPY EXTREME test score 9402
3D MARK TIME SPY test score 18964
3D MARK PORT ROYAL ray tracing test score 12897
3D MARK FIRE STRIKE ULTRA test score 125 71
3D MARK FIRE STRIKE EXTREME test score 22884
3D MARK FIRE STRIKE test score 34500
Tomb Raider · Shadow tested at 4K resolution with DLSS turned on and the highest ray tracing an average of 81FPS
Gears of War 5 tested at 4K resolution with ultra-high special effects and averaged 78.7FPS The average test under the highest extreme special effects is 85FPS
. The above is the entire content of this installation. Everyone is welcome to share and exchange. Thank you for reading
