『The full text is about 2300 words｜Reading takes 5 minutes』
In the hard decoration process, the importance of floor decoration is self-evident. Many people only know that the quality of ceramic tiles is crucial, but they ignore the importance of "Tile Paving" . As a retired foreman who has been dealing with decoration for half a lifetime, let me tell you the truth about floor decoration: "Tiles, three points rely on 'choice', and seven points rely on 'shop'" .
So whether the "tiling machine"'s technology and experience are well-equipped and rich, will directly affect the decoration effect of the ground. Next, this issue of home decoration special topic, Meijia Guide, will share with you the 8 details that should be given to the tiler when laying bricks , and 8 details that the tiler should give , I hope it can bring some help to everyone.
1. Do not make waveguide wires, and lay as much as possible
waveguide wires . Because they can play a role in space division, they were almost standard for ground decoration in the past. However, now the public is increasingly liking the minimalist style, so the design of the waveguide wire is obviously outdated. Moreover, with waveguide wires and without waveguide wires, the visual effect given by the ground is very different.
Living room floor waveguide wire design
Wave guide VS waveless guide
tiles are laid, which can not only gain visual integrity and beauty, but also reduce a lot of gaps. From the perspective of ground cleaning, the design of waveguide wires is not user-friendly. This is also one of the reasons why more and more people choose large-scale ceramic tiles. However, a friendly reminder is that not all living rooms are suitable for 750×1500 tiles. If the living room area is less than 30㎡, it is best to choose conventional 800×800 tiles.
2. Half-brick/cut tiles must be left at the corner of the wall or furniture hood
Since the specifications of the tiles are certain, and the indoor space and area are different, every household will calculate the "loss" when purchasing tiles, and the complete laying basically does not exist, so there will always be some "half-brick" and "cut tiles".
Half brick/cut bricks are all placed on the side
tiles will directly affect the visual experience, so you must remind the tiler to lay the bricks wherever you see the entrance door. Many people design patterns and shapes separately, hoping to be more beautiful, but in fact it is not as elegant as ordinary laying.
For some half bricks and cutting bricks, try to keep them in the locations covered by furniture such as sofas, TV cabinets, large beds, etc. This is a standardized and qualified brick laying method.
3. The wall tiles and floor tiles should be in the joints, and there is no need for grouting agent for the gaps
The wall tiles and floor tiles in the bathroom should be in the joints. Remember to be in the joints. Otherwise, it will be too ugly after laying the tiles. Nowadays, many people choose 800×800 tiles to the wall. After all, it is mainly because the large tiles have fewer gaps and are more atmospheric. However, the specifications of wall tiles and floor tiles commonly used in bathrooms can also be matched.
or not with the seams. The difference in the effect is too obvious. If 30×60 tiles are used, the specifications of floor tiles are exactly half of the former, so it is actually very simple to make the seams correct. What this depends on is not the bricklayer's skills and experience, but also the rigorous and responsible attitude.
In addition to laying the seams, do not use grouting agent in the bathroom wall tiles and floor tiles. It will get damp and fall off over time. It is recommended to use seam-applied agent to fill the seam directly, which is not only firm but also has a high aesthetic appearance.
4. You need to do matte before laying wall tiles
. The bathroom is dark and humid all year round, so there are certain requirements for laying wall tiles. For example, before laying tiles, the tiles must be "watered" and the walls must be "tie-tightened" and so on. Especially for "hair pulling". If the owner does not mention it, many tiles will skip this step to save trouble, and then the wall tiles will fall off in a few years after moving in.
Wall woven, simply put, it is to make the surface of the base layer of the wall not so smooth, and to enhance the "grasp" of the wall tiles through irregular surfaces.Many developers will do some matte matte before the new house is delivered. At this time, the tiler must check whether the matte matte matte matte matte made by the developer is qualified. If it is not qualified, it needs to be done again to avoid the situation where the bulge falls off due to insufficient holding strength in the later stage.
5. Don’t make sun corner strips, you should make crabapple corner
Whether it is the bathroom corner, or the balcony or kitchen, don’t install corner strip . It is undeniable that almost all bricklayers want to make sun corner strips, after all, sun corner strips are too easy to construct. On the other hand, few bricklayers are willing to do beautiful and atmospheric Begonia corners. After all, doing begonia corners requires a high construction technology for bricklayers and is relatively time-consuming.
Begonia corner full of high-end
Although house decoration should be mainly practical, aesthetics should also be taken into consideration. The sunny corners of the ceramic tiles seem inconspicuous, but in fact they are related to the beauty of the entire space. So I advise everyone to remind the bricklayer to be good. It is best to go to the construction site to keep an eye on the construction.
6. The bathroom wet area should have a slope
wet area as the shower area, which has certain requirements for the slope of the ground. If the slope is too small or the slope is not properly constructed, it will cause the water flow to flow into the floor drain naturally, which means that some of the ground will remain water-wet for a long time.
During construction acceptance, it is best to take a bottle of drinks or a few marbles to test whether the slope of the wet floor tiles passes. Don’t wait until the acceptance is completed and you will find that there is a problem with the slope when you experience it in the real shower.
After all, all ceramic tile projects are "one-time transactions". Once the construction is completed, it will be very difficult to demolish and modify later. Therefore, it is recommended that everyone be a bricklayer process and must be inspected on the spot.
7. The simpler the floor drain and floor drain tiling, the better the
. The seemingly small floor drain is also given in decoration design. For example, building materials such as floor drains, many people have begun to follow the trend of Internet celebrities in long floor drains, but they do not know that although long floor drains are quickly drained, they are also the most likely to hide dirt. Let’s talk about the tiling of the floor drain. It is important to remember that the simpler the floor drain tiling, the less likely it is to overturn. The fancy design makes the gaps difficult to clean and are easy to leak. Remember to brush the leak-blocking treasure.
long floor drain is high-end and atmospheric, but it is easy to hide dirt and dirt
Back-type floor drain is minimalist and practical, and it is more worth installing
Here, by the way, it is best to choose a big brand of floor drain, some miscellaneous or inferior floor drains, which are not only easy to rust, but also will also smell bad. It is far less than investing in some high-quality floor drains. In addition, if you can buy building materials like floor drains online, don’t buy them online. This will not only save money, but also ensure quality when choosing an official store.
8. Bathroom corner/bathroom basin should be used to prevent mildew and beauty glue
. In the construction project, the most important point is the "beautiful seams". Especially the corners of the bathroom and the waterproof strips in the bathroom basin, be sure to prevent mildew and beauty glue. Many bricklayers use their own inferior glass glue, but after moving in for less than half a year, they will find that all the glued areas are black and moldy.
Use inferior glass glue, which will definitely turn black and moldy within half a year.
In fact, the places where black and moldy are actually black and moldy are not only in the bathroom space, such as the countertop water barrier strips in the kitchen, the edge of the sink of the basin , the rubber strips in the refrigerator, the rubber strips in the window, and the rubber rings in the washing machine, etc. These places are often wet, so they are prone to black and moldy. Black and moldy actually means the growth of bacteria. Therefore, it is not good for living health. This is also the main reason why I say that bricklayers must use "mold-proof beauty glue".
—THE END—
said at the end:
This is the end of this issue’s special topic on tiles laying. For more home decoration content, please follow the "Beautiful Home Guide". See you in the next issue! If you have any other decoration knowledge topics you want to see, you can also leave a message!
