If I say that the collision bean float is very sensitive, it is no different from the sensitivity of the pure thin tail float. Many people have questions about this: if you use two such a large collision bean float, how can you say that you use a pure thin tail float? Is it possible to say that its sensitivity is almost exactly the same as that of a thin tail float? At first glance, isn’t the collision bean float like a bold tail float?
Yes, on the surface, the two quite large collision beans on the tail of the collision bean float are indeed larger and thicker than the thickened two or three-eye floats we commonly use. Its sensitivity should be lower, how could it be the sensitivity of a pure thin tail float?
OK. Today I will talk about why the sensitivity of the collision bean float is no different from the thin tail float.
The collision bean float uses two collision beans, usually red on top and yellow on the bottom. The collision bean is made of foam, it is light in the air and has a great buoyancy in the water. This is the characteristic of the foam. Fixing a collision bean at the top of the float will not add any amount to the entire float, and it can be almost negligible.
It is not feasible to use other materials to make beans, because it is difficult to have a lighter material than foam in weight. Even if the collision beans made of foam have a little portion, they only occupy a single eye at the top of the float tail. This eye cannot be placed under the water when adjusting the eye or fishing the eye. In other words, as long as this purpose collides beans are always above the water when fishing, it will not be able to produce buoyancy. Therefore, although this collision bean is fixed to the top of the float tail, it has no weight and does not allow it to play a buoyant role, then will the thin tail float of the collision bean still maintain its original weight, buoyancy and original sensitivity? The answer is yes.
Then, let’s talk about the yellow bean under the collision bean float. Does it affect the sensitivity of the thin tail float again?
Because the yellow colliding bean below has a large aperture in the center, it can slide up and down freely on the float tail. After the float falls into the water, the yellow bean below will float on the water surface all the time. In fact, the entire tail of the bean and the float are separated, without increasing the weight of the float at all. Therefore, the yellow collision bean did not affect the original sensitivity of the float itself.
According to the above situation, although we added two very eye-catching collision beans to the thin-tail float, we can fish very far with long rods or sliding float fishing, we did not cost fishing like using thick-tail floats, and would not lose some fish mouths and fish less. Instead, it maintains a high degree of sensitivity just like using a pure thin tail float, without losing mouths and fishing less.
Some anglers will say that although the eye-catching collision beans are added, they still cannot see clearly when there is a long distance of the next meal or top-up action. I would like to remind everyone that this kind of collision bean float, as long as you can see the two collision beans clearly and as long as you can see the changes in the distance between the two collision beans clearly, you can accurately arrest them. Because as long as the fishing eye is set at three or four eyes, there will be a distance between the two collide beans from one to two eyes. As long as the distance is broken, there will be a change, and you can see this change, you can lift your rod and stab the fish. For example, there are two eyes between the two beans on the upper and lower collisions. When there is a fish mouth, it becomes one eye, or the two beans lean against each other, causing a collision, which means that there is one eye or two eyes next to it. At this time, you need to lift your rod and stab the fish. If the distance between the two upper and lower collides beans changes from two eyes to three eyes or four eyes, and the distance is widened, it means that it is the floating face of the upper top, and you can also lift the rod and stab the fish. This change in the distance between two collide beans at a distance will definitely be more clearly seen than the conventional bold float, which is a small amount of lower or upper top.
Generally speaking, this kind of collision bean float is indeed a very advantageous type of float for fishing far away. It is worth using it widely when fishing far away.
collision beans can be purchased online. You can use the purchased collision beans to make homemade collision beans floats for thin-tailed floats that you don’t want to use. This is cheap, which solves the problem of insufficient sensitivity in fishing distance, or the float cannot be seen clearly, and the effect is also very good.
In order to avoid the collision beans below and the floating beans are stuck together and cannot be separated after entering the water, the tip of the yellow beans is facing downwards, so that the contact area is smaller and will not stick together after being dipped in water. The beans I used before were round and often stick to the beans of the floating belly, which was very difficult to use. Now it has been improved. The beans are not round, but are round and pointed at the end, so there is no problem. By the same token, the red top bean above also needs to be pointed downward to reduce the contact area with the lower beans. After being dipped in water, it will not stick together and cannot be separated, but can be separated smoothly. This link is very important. Never do it wrong. If it is wrong, it will not work. Either the beans will always stick together and cannot be separated from the floating belly, or both of them will always stick together and cannot be separated. As long as I do the same as I said, this phenomenon will not occur. It will be very easy to use and very satisfied.
When operating, first pass the yellow lower bean into the floating tail, and then insert the upper bean in a target place. It doesn’t matter if it is tight when inserted. Just drop a drop of 502 glue, and wait for a while, it will solidify and stick firmly. A collision bean will be done. It is very simple to operate.
