question bank source: Production Safety Simulation Examination Yitong Official Account Mini Program
2022 Large Amusement Facilities Operation Certificate Examination Question Bank is a large Amusement Facilities Operation Judgment Question Simulation and Prediction Paper! The 2022 large amusement facilities operation examination question bank and online mock exam will be compiled based on the latest textbooks for large amusement facilities operation. Large amusement facilities operation exercises are available at any time based on the test bank for the production safety simulation exam.
1. [Multiple choice question] Units responsible for the accident in which a special equipment accident occurs shall be fined by the special equipment safety supervision and management department in accordance with (). (ABC)
A. If a general accident occurs, a fine of not less than RMB 100,000 and not more than RMB 200,000;
B. If a major accident occurs, a fine of not less than RMB 200,000 and not more than RMB 500,000;
C. If a major accident occurs, a fine of not less than RMB 500,000 and not more than RMB 2 million will be imposed.
2. [Multiple choice question] If a special equipment accident occurs and one of the () acts constitutes a crime, criminal liability shall be pursued in accordance with the law; if an illegal act constitutes an illegal act stipulated by relevant laws and regulations, an administrative penalty of will be imposed in accordance with the law; if it does not constitute an illegal act stipulated by relevant laws and regulations, the quality and technical supervision department and others will be fined not less than RMB 4,000 and not more than RMB 20,000. (ABC)
A. Forged or intentionally sabotaged the accident scene;
B. Refused to accept investigation or refused to provide relevant information or information;
C. Obstruction or interference in the report and investigation and handling of special equipment accidents.
3. [Multiple choice question] The seat belt can be used separately on the facilities of (). (ABCD)
A, slightly sway
B, slow lifting speed
C, no flip
D, no danger
4, [Multiple choice question] Before the new special equipment is put into use, the user unit must go to the local area, city or above special equipment safety supervision organization to complete the registration procedures, and can only be put into use after registration. When registering, () information should be provided. (ABCDE )
A, "Special Equipment Registration Registration" (2 copies per unit);
B, acceptance inspection report and "Safety Inspection Pass" mark;
C, "Special Equipment Operator Qualification Certificate" for operators;
D, maintenance contract signed with the maintenance unit, or new special equipment for manufacturing enterprises Provide free maintenance certificates, or maintenance responsibility letters signed with personnel who have obtained special equipment maintenance qualifications in this unit;
E, the "Special Equipment Installation, Renovation, Maintenance and Maintenance Qualification Certificate" of the maintenance unit, or the "Special Equipment Operator Qualification Certificate" of the maintenance personnel of this unit;
5, [Multiple choice question] Standard transmission gear transmission is normal, and should not have: () ( AB )
A, abnormally partially engaged
B, partially worn
C, damaged
D, crack
6, [Multiple choice question] The technical archives of the amusement facility user unit include at least (). (ABCDE)
A, amusement facilities registration form. Daily operation and routine inspection records.
B, factory random documents of equipment and its components, including large-scale amusement facilities design documents, design appraisal reports, product quality certificates of manufacturing units, installation and use and maintenance instructions, etc., as well as technical documents and materials for the installation (or and transformation, major repair) process specified in the safety technical specifications.
C, annual equipment maintenance plan and implementation status (including records of overhaul and acceptance materials, etc.).
D, annual training assessment plan, employee training records and certificates.
E, daily maintenance records of large amusement facilities and their safety protection devices, measurement and control devices and main components;
7, [Multiple choice question] The amusement facilities use and maintenance instructions should include ().(ABCDE)
A, equipment introduction; structure overview; main technical parameters;
B, installation and debugging; operation and precautions and signs;
C, maintenance and repair instructions;
D, equipment failure emergency treatment;
E, lubrication part description;
8, [Multiple choice question] Basic requirements for the safety equipment of amusement facilities (). (ABCDE)
A. According to the performance, structure and operating mode of the amusement facilities, corresponding forms of safety devices must be set up. For amusement facilities with a height of more than 20m, anemometer should be installed at a height of 10m.
B and viewing car must be able to rotate forward and reverse, and the parking switch should be set in a convenient position.
C. The lifting mechanism should be safe and reliable, and crawling, rushing and abnormal vibrations are not allowed during operation. By increasing the friction force, no obvious relative sliding between the friction surfaces is allowed.
D. The manned device is parked at any position in the lifting section under the rated load, and the lifting mechanism should be able to start smoothly. The lifting section should have a safe passage to guide passengers.
E. Where there is a possibility of human body or object falling and causing casualties, a safety net should be set up. The connection of the safety net should be reliable, and the performance of the safety net should comply with the requirements of the flat network in the "Safe Net" (GB5725).
9. [Multiple choice question] If a special equipment user unit has one of the () circumstances, the special equipment safety supervision and management department shall order it to correct the problem within a time limit; if it fails to correct the problem within the time limit, it shall be ordered to stop use or suspend production and business and be fined between RMB 2,000 and RMB 20,000 and RMB 20,000. (ABC)
A. Those who fail to set up special equipment safety management agencies or are equipped with full-time and part-time safety management personnel in accordance with the provisions of the " Special Equipment Safety Supervision Regulations ";
B. Those who engage in special equipment operations have not obtained the corresponding special worker certificate and are on duty;
C. Those who do not provide special equipment safety education and training for special equipment operators.
10. [Multiple choice question] Before special equipment is put into use, the user unit shall check whether it is attached with () and other documents required by safety technical specifications. (ABCDE)
A, design file
B, product quality certificate
C, installation instructions
D, use and maintenance instructions
E, supervision and inspection verification
11, [Multiple choice question] Surface requirements for fiberglass parts: () (ABCD )
A. No cracks or damage are allowed. The transition at the corners should be smooth. The inner surface that touches the passengers should be neat. No glass head should be exposed. The edges of the fiberglass parts should be flat and smooth. No layered
D. FRP pieces should be directly connected to the stressed parts.
12. [Multiple choice question] Application for supervision and inspection of B and C grade amusement facilities should meet the conditions () (ABCDE )
A. The enterprise responsible for installation, repair and renovation construction shall obtain an installation, repair, renovation license. The construction category and level of the license shall be consistent with the construction project and shall be within the validity period;
B. The construction notice has been made in accordance with regulations before installation, repair and renovation construction;
C. The installed amusement facilities are products that have obtained a manufacturing license and comply with Requirements for safety technical specifications;
D. The equipment being transformed and repaired has completed the use registration procedures;
E. There are qualified certified operators who can ensure normal operation. The newly installed equipment has initially established a necessary safety management system;
13. [Multiple choice question] Each equipment in mobile amusement facilities must provide () materials when registering for use.(ABCDE)
A, the registration cancellation document issued by the original registration authority (used in China by moving to the land);
B, mobile amusement facilities registration form (in duplicate);
C, mobile amusement facilities inspection report and "Safety Inspection Qualification" mark;
D, mobile amusement facilities maintenance and operator qualification certificate;
E, maintenance system and relevant responsible persons; relevant information of safety management personnel; use and operation safety management system;
14, [Multiple choice question] Safety inspection of amusement facilities in tourist areas (). (ABC)
A, operation inspection.
B, check regularly.
C, check from time to time.
15. [Single choice question] "Special Equipment Operator Certificate" is reviewed once every (). (D)
A, 1 year
B, 2 year
C, 3 year
D, 4 year
16, [Single choice question] The "Regulations on Safety Supervision of Special Equipment" stipulates that () units should establish emergency rescue plans for major accidents. (C)
A, hazardous chemical unit
B, production and operation unit
C, special equipment unit
17, [Single choice question] The following is not a cockpit safety device (). (D)
A, safety belt
B, handle
C, safety gear lever
D, the above are all
18, [Single choice question] In order to eliminate static hazards in the production process, the effective measures that can be adopted are (). (C)
A, protective grounding
B, tip discharge
C, grounding discharge
19, [Single choice question] The decorative lighting voltage of passengers' easily contacted parts (height less than 2.5m or safety distance less than 500mm) should be a safe voltage not greater than ()V. (C)
A, 24
B, 36
C, 50
D, 220
20, [Single choice question] The following amusement machines that do not belong to the category of viewing cars are (). (B)
A, spaceship
B, viewing tower
C, flying carpet
D, pirate ship
21, [Single choice question] The following amusement machines that belong to the horse-turning category include (). (D)
A, Brave Turntable
B, Flying Tower
C, Brave Turntable; Flying Tower
D, Wave Swing; Octopus
22, [Single Choice Question] The error of the safety device for hanging seats is () (C )
A, hanging hanging parts
B, protective parts
C, . handle
D, cockpit or seat
23, [Single choice question] The basic form is a circular border with slashes, which is the () logo. (A)
A, prohibition flag
B, warning flag
C, instruction flag
D, prompt flag
24, [Single choice question] The process of safe pressing bar should be slow, the maximum force applied to the user, and the adult should not be greater than ()N. (C)
A, 80
B, 100
C, 150
D, 200
25, [Single choice question] Outdoor amusement facilities shall not be operated and used under dangerous weather conditions such as storms. Amusement facilities with a height exceeding () m must be stopped when the wind speed is greater than 15m/s. (D)
A, 5
B, 10
C, 15
D, 20
26, [Single choice question] Classified by the motor operation working system, S1 represents: () working system.(D)
A, long-term
B, short-term
C, periodic
D, continuous
27, [Single choice question] Electrical switches operated by passengers should use a safe voltage not greater than ()V. If the requirements cannot be met, necessary measures must be taken to ensure personal safety. (B)
A, 12
B, 24
C, 36
D, 50
28, [Single choice question] According to the notice of adjusting the grading of large amusement facilities, the gyro inclination angle ≥70° or the rotation diameter ≥ () m is a large A amusement facilities. (B)
A, 10
B, 12
C, 14
D, 15
29, [Single choice question] The steps width of the import and export of amusement facilities shall not be less than () mm, and the height is () mm. (D)
A, 200mm, 150-200mm
B, 210mm, 200-250mm
C, 220mm, 150-250mm
D, 240mm, 140-200mm
30, [Single choice question] If a tourist is found to have an electric shock accident during the recreation, the steps to be taken, () 1. Quickly notify the superiors and medical units, 2. Take necessary first aid measures such as artificial respiration 3. Transfer the electric shock to the appropriate position, and immediately disconnect the main power switch of the machine. (C)
A, A1-2-3-4
B, 1-3-2-4
C, 4-3-2-1
D, 1-3-4-2
31, [Single choice question] According to the " Safety Production Law of the People's Republic of China ", my country's safety production work adheres to the () policy. (C)
A. People-oriented, work and rest combination, healthy development
B. Quality first, safety first, comprehensive development
C. Safety first, prevention first, comprehensive management
D. Prevention first, prevention first, comprehensive management
D. Prevention first, prevention and fire prevention combined, comprehensive management
32. [Single choice question] The operation, management and maintenance personnel of the amusement machine should be trained, and the operation and maintenance personnel should be assessed in accordance with the relevant regulations of () and hold a certificate to work. (A)
A, National Quality and Technical Supervision Bureau
B, Provincial (City) Quality and Technical Supervision Bureau
C, Provincial (City) Labor Bureau
D, Ministry of Construction of the People's Republic of China
33, [Single choice question] A special equipment accident caused more than 3 people to die, or more than 10 people to seriously injured, or more than 50 people to directly suffer economic losses of less than 10 million yuan and less than 50 million yuan, the accident is () accident. (B) If the special equipment user unit fails to conduct regular daily maintenance and regular self-check on special equipment in use in accordance with Article 27 of the "Regulations on Safety Supervision of Special Equipment", or regularly check and inspect the safety accessories, safety protection devices, measurement and control devices and related auxiliary instruments of special equipment in use, and make records, the special equipment safety supervision and management department shall order the special equipment safety supervision and management department to correct the problem within a time limit; if the rectification is not corrected within the time limit, it shall be fined (); if the circumstances are serious, it shall be ordered to stop use or suspend production and business rectification. (B)
A,
A,
B,
B,
C, 000 or more than 50,000 yuan,
C,
D,
D,
00 or more than 100,000 yuan,
35, [Single choice question] If a special equipment fails or abnormal situations occur, the user unit shall conduct () inspection of it and eliminate the potential dangers of accidents before it can be put into use again. (C)
A, local
B, key
C, comprehensive
D, targeted
36, [Single choice question] The special equipment user unit shall register with the special equipment safety supervision and management department of the municipality directly under the central government or the prefecture-level city within () days.(A)
A, 30
B, 45
C, 60
D, 90
37, [Single choice question] The notice of jointly issuing the "Regulations on Safety Supervision and Management of Entertainment Machines and Amusement Facilities" by National Technical Supervision Bureau , National Tourism Bureau , the Ministry of Public Security, Labor Bureau , and the State Administration for Industry and Commerce jointly issued the "Regulations on Safety Supervision and Management of Entertainment Machines and Amusement Facilities" in () year. (C)
A, 1986
B, 1989
C, 1994
D, 1996
38, [Single choice question] Under normal circumstances, unactivated metal shells, metal pipe grooves, cable metal protective layer, transformer secondary circuits, etc. must be reliably connected to the PE line of the power line, and the protection of low-voltage distribution system repeat grounding resistance should not be greater than ()Ω. (B)
A, 4
B, 10
C, 0.25M
D, 0.5M
39, [Single choice question] The grounding resistance of the lightning protection device should not be greater than ()Ω. (D)
A, 4
B, 10
C, 20
D, 30
40, [Single choice question] For important connectors, you must take anti-loosening measures. The following are commonly used anti-loosening methods except for (). (A)
A, welding
B, spring washer
C, double nut
D, shaft end baffle fixed pin
41, [Single choice question] A recreation facilities with a height of more than 20m should be equipped with an anemometer at the height (). When the wind speed is greater than 15m/s, it must be stopped. (B)
A, 5m
B, 10m
C, 15m
D, highest
42, [Single choice question] () is an accident caused by problems in production and operation units in terms of production and operation management or an accident caused by dereliction of duty and malfeasance of administrative departments that have the responsibility of approval and supervision of relevant matters of production safety. (C)
A, major accident
B, major accident
C, liability accident
D, human accident
43, [Single choice question] (), all should have limit position restriction devices. (C)
A, horizontal traction lifting system
B, lifting system running along the circumference
C, lifting arm rotating around the fixed axis fulcrum, component swinging around the fixed axis
44, [Judgement Question] Whenever the wind speed is greater than 10M/S in bad weather, large viewing cars, flying towers, and scooters should stop running. (×)
45. [Judgement Question] The rigid part hanging entertainment machine does not belong to the hanging rotary entertainment machine. (×)
46. [Multiple choice question] The brake device is not adjusted properly, sometimes the brake is too fast, and sometimes the brake does not work, which will cause unsafe or fear to the passengers. (√)
47. [Multiple choice question] The purpose of formulating an emergency rescue system for major accidents is to study the victims, control the development of the situation, do a good job in on-site recovery, and find out the cause of the accident. (√)
48. [Judgement Question] If a major accident in special equipment and an accident below the level occurs, administrative penalties and punishments shall be imposed in accordance with the relevant provisions of the "Regulations on Safety Supervision of Special Equipment", administrative penalties and punishments shall be imposed; if a crime constitutes a crime, criminal liability shall be pursued in accordance with the law. (√)
49. [Judgement Question] When the inspected unit has objection to the inspection results, it may submit it to the inspection agency in writing within 15 days from the date of receipt of the inspection report. The inspection agency must provide a written reply to the objection raised by the inspected unit within 15 days. ((√)
50. [Judgement Question] As long as the unit with the detection capabilities can detect the amusement facilities. (×)
51. [Judgement Question] The hanging rotary amusement machine is divided into winding parts hanging amusement machine and rigid parts hanging amusement machine. (√)
52. [Judgement Question] The special equipment accident caused by natural disasters , war and other forces are not considered special equipment accidents.(√)
53. [Judgement Question] The user units of large amusement facilities shall place safety precautions and warning signs for the use of large amusement facilities in a prominent position that is easy for passengers to pay attention to. The safety precautions and warning signs must have Chinese text descriptions or schematic patterns specified in the standards. (√)
54. [Judgement Question] When large amusement facilities and their safety protection devices leave the factory, they must provide necessary design documents, product quality certificates, installation and use and maintenance instructions, non-destructive inspection plans and operating guidelines in accordance with the safety technical specifications and other safety technical specifications such as "Regulations on Safety Technical Supervision of Large Amusement Facilities", and provide users with necessary spare parts and special tools. (√)
55. [Judgement Question] Large amusement facilities installation, transformation and maintenance units must hire large amusement facilities operators who hold the "Special Equipment Operator Certificate". They should conduct pre-job safety education and training for the hired personnel based on the actual situation of the unit to ensure that they have the necessary safety knowledge of large amusement facilities. (√)
56. [Judgement Question] Construction units for installation, renovation, or major repair of large amusement facilities shall inform the quality and technical supervision bureau of the municipality directly under the central government or prefecture-level city of the construction site of the construction site in writing before construction, and the construction can be carried out after informing them. (√)
57. [Multiple choice question] Operators and safety management personnel of large amusement facilities installation (including installation of renovation construction), maintenance, operation, etc. must follow the relevant safety technical specifications, pass the assessment by the quality and technical supervision administrative department, and obtain the "Special Equipment Operator Certificate" issued by the quality and technical supervision department, before they can engage in corresponding operations or management within the scope of the licensed project. (√)
58. [Judgement Question] Large amusement facilities inspection agencies should inform the relevant provincial special equipment safety supervision agencies of the annual appraisal and inspection plan at the beginning of January each year, and within 5 working days, the specific appraisal and inspection work arrangements shall be notified in writing to the local special equipment safety supervision agencies of the local special equipment safety supervision agencies where the equipment is used. (√)
59. [Multiple choice question] Operators of large amusement facilities must obtain the "Special Equipment Operator Certificate" for the corresponding project in accordance with the requirements of the " Special Equipment Operators Supervision and Management Measures " to obtain the corresponding project "Special Equipment Operators Certificate" before they can engage in related work. (√)
60. [Judgement Question] Large amusement facilities maintenance units must obtain the maintenance license of the Quality and Technical Supervision Bureau of the province, autonomous region, or municipality directly under the Central Government before they can engage in maintenance activities within the scope of the licensed project. (√)
61. [Judgement Question] Before using the vertical transportation device of sliding-mode construction , the design unit should organize the production, installation, use and inspection and acceptance of the supervision unit. (×)
62. [Multiple choice question] The safety protection device is a device used to control position, speed, prevention, and pass the safety production simulation test and stop falling. (√)
63. [Judgement Question] Safety production management, adhere to the principle of safety first and prevention first. (√)
64. [Judgement Question] The main safety devices of the cockpit include safety belts, safety rods, hydraulic lock safety rods, double fuse door pins, and handrails. (√)
65. [Judgement Question] If the party forged or intentionally damaged the scene of a special equipment accident, destroyed evidence, failed to report the accident in a timely manner, etc., causing the responsibility for the accident cannot be determined, he shall bear the main responsibility (√)
66. [Judgement Question] If the party forged or deliberately damaged the scene of a special equipment accident, destroyed evidence, failed to report the accident in a timely manner, etc., resulting in the responsibility for the accident cannot be determined, he shall bear the full responsibility. (√)
67. [Multiple choice question] When the viewing car suddenly has a power outage during operation, it is necessary to explain the situation to the tourists through the radio in a timely manner, so that the tourists can wait with confidence, cut off the original power supply immediately, and then use a backup power source to evacuate the tourists.(√)
68. [Judgement Question] When the limit switch does not work, check whether the spring is damaged, whether the swing rod is reset, the contact effect and whether the installation position is moved. (√)
69. [Multiple choice question] Those who hold the "Boiler Pressure Vessel Pressure Pipeline Special Equipment Operator Qualification Certificate" can operate entertainment facilities. (×)
70. [Multiple choice question] If a licensed worker cheats in the exam or obtains the "Special Equipment Operator Certificate" by other deceptive methods, the "Special Equipment Operator Certificate" shall be revoked, and the licensee shall not apply for the "Special Equipment Operator Certificate" again within 4 years. (×)
71. [Multiple choice question] Overhead tour bus is a recreational facility included in the safety supervision department of quality construction supervision. (√)
72. [Multiple choice question] According to the degree of danger, large amusement facilities are divided into three levels A, B, and C. (√)
73. [Multiple choice question] Before each operation, the worker and service personnel must explain safety precautions to tourists and check and confirm the safety device. (√)
74. [Judgement Question] Water amusement facilities should undergo a major equipment safety inspection once a week, and hidden dangers are found and promptly rectified. If accidents and signs occur, the "three no-send" system for handling accidents should be strictly implemented. (√)
75. [Multiple choice question] When measuring the insulation resistance of the rectifier transformer winding to the metal shell , you can measure it without disassembling the secondary wiring. (×)
76. [Multiple choice question] Amusement parks (fields) and other operating units have no problem with the amusement machine and amusement facilities as long as they are tested once a year according to regulations. (×)
77. [Judgement Question] Amusement facilities user units must establish security management system to clarify the safety responsibilities of relevant personnel; improve various safety management systems and strictly implement them. (√)
78. [Judgement Question] Amusement facilities should set up eye-catching safety signs in necessary places and places, with green as the instruction sign. (×)
79. [Judgement Question] Various safety and safety production simulation tests on the amusement machine are tools to protect operators. (×)
80. [Judgement Question] The operating units of amusement machines and amusement facilities are responsible for providing engineering geological data and meteorological data; the production enterprises are responsible for providing foundation construction drawings; the construction units must construct according to the foundation construction drawings; the production enterprises or installation units can only install them after the project foundation acceptance is passed. (√)
81. [Judgement Question] The amusement machine is in operation, and the operator is strictly prohibited from leaving the post without authorization. (√)
82. [Multiple choice question] In special circumstances, special equipment operators can engage in corresponding operations or management work without having to pass the assessment by the special equipment safety supervision and management department in accordance with relevant national regulations and obtain a national unified format special operation personnel certificate. (×)
83. [Judgement Question] The special equipment user unit shall submit regular inspection requirements to the special equipment inspection and testing agency one month before the expiration of the validity period of safety inspection. (√)
84. [Judgement Question] If a special equipment has serious accident hazards, has no transformation or maintenance value, or exceeds the service life stipulated in the safety technical specifications, and the special equipment user unit fails to scrap it and cancel it from the original registered special equipment safety supervision and management department, the special equipment safety supervision and management department shall order the special equipment safety supervision and management department to correct the problem within a time limit; if it fails to correct the problem within the time limit, it shall be fined not less than RMB 100,000 and not more than RMB 300,000. (×)
85. [Judgement Question] Enterprises that produce amusement machines and amusement facilities must be approved and registered by the industrial and commercial administrative department, obtain a business license, and carry out production and operation activities within the approved business scope. (√)
86. [Judgement Question] Production and operation units must abide by the "Production Safety Law of the People's Republic of China" and other laws and regulations on production safety, strengthen production safety management, establish and improve production safety responsibility systems, improve production safety conditions, and ensure production safety.(√)
87. [Multiple choice question] The wearing requirements for climbers: wear loose clothes, wear cloth shoes, and wear seat belts. (×)
88. [Multiple choice question] During the service period, mobile amusement facilities should properly preserve technical materials including material certificates, test reports, inspection reports, drawings and calculation books. (√)
89. [Multiple choice question] The installation, maintenance and operation of mobile amusement facilities shall be carried out by the operator who obtains the special equipment operator certificate. The operator certificate shall be issued by . The General Administration of Quality Supervision, Inspection and Quarantine (√)
90. [Multiple choice question] The power supply system of mobile amusement facilities shall meet the requirements: the power supply system shall meet the needs of facility operation control and safety protection, and meet the requirements for normal use of equipment under local environmental conditions. When power is powered by self-provided power, the user shall provide a verification and qualification report of the self-provided power supply; when the riding device cannot return to the platform or a safe position in case of a power failure, an emergency power supply device shall be set up and can be started within 5 minutes. (√)
91. [Multiple choice question] The metal structure of mobile amusement facilities should meet the following requirements: the metal structure should have sufficient strength and stiffness, and no connection gap, shaking or deformation that affects the normal operation of the equipment should be allowed; the connection method of the metal structure should be firm and reliable, which is convenient for the installation and disassembly of the equipment, and elastic washer, elastic retaining ring, opening pin and self-locking nut that produce over-plastic deformation should be updated before each installation and shall not be continued. (√)
92. [Multiple choice question] Amusement facilities included in the safety supervision of the quality and technical supervision department, including large manned amusement facilities with operating heights higher than or equal to 2m from the ground. (×)
93. [Multiple choice question] automatic aircraft passenger cockpit is installed on the same arm, and the cockpit can only lift and lower the horizontal plane around the central vertical axis. (×)
94. [Multiple choice question] The cockpit of the autonomous aircraft is installed on the same arm, and the cockpit can only rotate around the central vertical axis on the horizontal plane. (×)
95. [Multiple choice question] The amusement machine will be run at least three times before it is opened. Only after confirming that everything is normal can the machine be officially started. (×)
96. [Multiple choice question] At least one locking device should be installed in the closed hoist of the viewing car amusement facilities. (×)
97. [Judgement Question] The quality and technical supervision department shall implement safety supervision and inspection of the production, use and inspection and testing of mobile large amusement facilities in accordance with the "Regulations on Safety Supervision of Special Equipment" and relevant regulations, and shall keep records. If problems are found, they shall be dealt with in a timely manner. When implementing safety supervision and inspection, more than two special equipment safety supervision personnel should participate and present the special equipment safety supervision personnel's certificates. (√)
98. [Judgement Question] Those who illegally direct special equipment operations shall be ordered to correct the situation and shall be fined not less than RMB 2,000 and not more than RMB 10,000. (×)
99. [Multiple choice question] Important shaft parts refer to important shaft (pin) parts refer to shaft and pin parts that will cause damage to passengers when they fail, such as spindle, central axis, seat hanging shaft, wheel shaft, oil (gas) cylinder upper and lower support pin shaft, seat support arm upper and lower pin shaft, etc. (√)
100. [Judgement Question] Operators and related management personnel of boilers, pressure vessels, , elevators, lifting machinery, passenger cableways, large amusement facilities, special motor vehicles in the field (factory) shall pass the assessment by the special equipment safety supervision and management department in accordance with relevant national regulations and obtain a special operator certificate in the national unified format before they can engage in corresponding operations or management work. (√)
supports the test questions for precise large-scale amusement facilities operation tests in various regions across the country, supports safety qualification certificates, special operation certificates, , professional skills appraisal and other job question bank exercises.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-