Xu Shui’s colleagues who assisted the production went back today.
Today, the ceiling line and the sub-dashboard were replaced by people here! I have to say that the people here are far less efficient in their work than those in Xushui! People on Xushui can get thirty small ceiling lines and thirty wires and sub-dash dashboards in an hour. People on Xushui can't get thirty wires in an hour! Each of them was produced with 220 lines, and they had not finished their work until after 10 o'clock in the evening. They were all newcomers working, and there were many problems. It's a lot of trouble, just changing the line is a waste. It was eleven o'clock after we cleaned up.
I have never recorded a problem in the third test. The main reason is that if I record the problem, Sister Chen will have to sign and be punished. Sister Chen’s test is indeed fast, but it’s too big! Because I am all newcomers today, I dare not check it out randomly, and each wire is stuck on the board to check it out. The problem that Sister Chen did not detect is as follows:
1 The backbone is covered with blue tape. 2
2 branches leaked on blue tape. 2
3 braided tubes were not sealed with PVC tape. One
4 two branches should be wrapped for 50mm before qualifying, but it will be qualifying before qualifying. The outgoing line of 1
5 branch is incorrectly located. The three branches have two outgoing points, which are 30mm apart from the upper and lower sides. As a result, there is no distance of this 30mm, which leads to one branch being 10mm shorter. 1
6 snap 010336 is in the opposite direction. The long side should be super right, and the short side should be on the left. 1
7 sponge exceeds 200mm and does not use PVC dots to wrap it. 4
8 snaps 010336 are only wrapped around one side and the other is not wrapped around. One
9 antenna is required to be completely wrapped with cloth, but the result is a bare wire. The 4
10 branch outlet lines have the wrong direction, and they should have been straight out. As a result, the person who wiring the line hangs the wrong board and becomes the side out! Just forget about 1
leaking line, but it looks like it is filled.
When I find these bad things, I will notify Sister Chen as soon as possible and tell her to stick the inspection board when inspecting. She smiled embarrassedly and said, "Fortunately, I have you, so I'm specifically blocking it!" But the problem is that I'm also very busy. In addition to checking the wires that Sister Chen has inspected, I also have to put bubble bags , tie it, wrap it back, scan the code, pack it, and pack it. I can't pull it open and I can't free it. She checked it all over and I could save a lot of time.
Deputy squad leader told me that the ceiling factory reported that the bubble bag leaked again today! November 18th! That's what I did! How could I have bad things? I was very surprised! Because I did it, I made sure that each of them was covered with bubble bags. After checking, I wrapped them back, and then scan the code to check it out again when packing. Why are there any missing bags? I was speechless, wanting to cry without tears, and my heart was mixed! How did I promise with the squad leader at that time?
Sister Chen comforted me and said, "I have said a long time ago that it is impossible for people to do a job perfectly and it is impossible to be foolproof! I have reported what others have done five times before. This is the first time you have reported it. It's okay! Don't let a bad person scare yourself to death!" It's okay if she doesn't comfort me, but when she comforts me, I feel even sadder!
lunch break time squad leader asked everyone to have a meeting beside the sun sensor table. I heard from the squad leader that he was not easy for him. If everyone doesn’t do a good job, he will have to be quarrel! ! I was quarreled by my leader seven times a day! I have to say that he has really strong psychological quality! If it were me, I would have become that crazy!
talks about which lines are most likely to have problems. When it comes to the small ceiling line, leaking bubble bags is a big problem. My tears immediately "swept" down! I do feel very guilty. I would like to remind you of this problem every time I held a morning meeting. I repeatedly confirmed it when I did it, but there was still something missing! What's the reason? Didn't check carefully!
What did I do on November 18th? I opened my headlines and turned to the record on November 18th.That day, when I got off work at half past ten, the deputy squad leader went over to help, helping to pack bags and boxes! Could it be... At that time, I pressed a lot of sub-dashboard lines, and I was busy inspecting the sub-dashboard!
is my problem! If others help, even if there is a problem, you can’t say it’s someone else, otherwise no one will help you in the future! The most important thing is that after the helper finished his work, I let him pass without checking! It's indeed my problem! Shuting, you must never make such a problem again in the future! Start today! November 26, 2022! No matter who comes to help with the work, you must confirm it yourself and make sure it is correct and then pass it!
After dinner in the evening, Section Chief Wu held a meeting for us. It also mentions quality issues. He said that the key dimensions of each wire must be measured to ensure that the dimensions are within the tolerance range.
It is indeed not easy to look at our squad leader. You must calm down and do the work in your hands, and don’t implicate him and be scolded!
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-