I am Axiao, I haven’t seen you for a week, I miss you very much!
A few weeks ago, I introduced the content of the first chapter of the Intermediate Fire Facilities Operator Practical Examination. This week, we will continue to explain the Intermediate practise to talk about Chapter 2, hoping to help you!
Many people are worried that it will be difficult to take the actual exam. In this , Axiao , I just want to say that you don’t have to worry too much. The actual exam is careful and attentive, the exam is careful, and the preparation is carefully. If you have the conditions, you must operate it on real equipment, so that you can get twice the result with half the effort.
If you feel that the articles of Axiao are useful, remember to share them with friends or circle of friends in need! Thank you for your support from consumers!
Opening Introduction
Fire Facilities Operator Intermediate
Fire Facilities Operator Examination is mainly divided into two subjects: theoretical examination and practical examination.
Theory General examination time is March, June, September and December of each year. If nothing unexpected happens, it is on the third weekend of that month. The specific examination time and location should be published as standards according to the arrangements of the provincial appraisal stations.
The answer time for the theoretical exam is 90 minutes, which is relatively abundant. The total score of the test paper is 100 points, and the passing standard is 60 points. Among them, there are 100 questions, 60 multiple choice questions, and 40 judgment questions, with 0.5 points for each question. Generally, as long as you prepare carefully and read the questions several times, it is not difficult to pass.
practical examination time generally needs to be determined according to the registration time. The specific examination location is at the appraisal station of the province to which the registration is registered. Students who refer to it remember this and don’t go the wrong way. Because the
practical examination is relatively relaxed, the examination time is mostly based on actual conditions, with a total score of 100 points, and the passing line is 60 points. The examination content mainly includes four classrooms: 27 points for water fire extinguishing classroom, 25 points for control room, 23 points for fire extinguishing classroom, and 25 points for fire prevention patrol classroom.
practical operation generally requires boldness and carefulness. It is very important to watch more practical videos in daily life. If necessary, you can actually train offline.
Generally speaking, the examination for firefighters in buildings is not difficult. As long as the preparation method is correct and persists, you can basically pass it.
Chapter 2: Fire Control Room Monitoring
Back to the Intermediate Fire Facilities Operator Practical Examination, what we are going to learn today is the content of Chapter 2 Fire Control Room, which is mainly divided into three parts. A Fei will briefly talk about it one by one, hoping to help consumers who prepare for the exam.
Chapter 2 Section 1
controller multiple information query
History query
We can view the status information of the current controller through the controller panel. For example, in the picture above, the signal light on the right is lit, and the fire alarm information can be seen on the electronic screen on the left. If the signal light is not lit, it means that this state does not appear.
If you miss the time and want to query the previous fire alarm information, you can enter by pressing the "Record Check" button on the controller panel and follow the steps to query.
"Fire Alarm" information query steps:
1. Press the "0-Record Check" key to query.
2. Press the corresponding numeric key "2" to query.
3. If you want to query the previous information, press the "up and down" keys to turn the page and query.
4. After the query is completed, click the "Cancel" key to return to the main interface. The method of querying the history record of
is similar to the method of querying the fire alarm information mentioned above, and is also divided into four points.
1. Press the "0-Record Check" key to query.
2. If there is a password, enter the password, and if there is no, press "Confirm".
3. Because the query is the run record, you need to press the numeric key "1".
4. In the running record, we can see the relevant information and query the history record through the "up and down keys".
5. After the query is completed, press the "Cancel" key to return to the main interface.
or above is the entire content of the controller information query section. In the actual exam, this part will be evaluated using the "manual operation + oral answer" method, accounting for 6 points, of which information query accounts for 4 points and historical record query accounts for 2 points, which is a must-score item.
Chapter 2 Section 2
Replacement of printing paper
Control method setting
Bus control fire linkage equipment
Chapter 2 Section 2 is mainly divided into three parts, namely the replacement of printing paper, control method setting, and bus control fire linkage equipment. It is not difficult to learn.
Print paper replacement requires a total of four steps, namely:
1. Press the "Open Key" SEL and the light is off.
2. Press the slots on both sides and remove the front cover.
3. Remove the printer.
4. Remove the printer reel.
5. Replace the scroll with the new paper in the guide groove.
6. The printer paper should be exposed and press LF to reset. There are relatively more operations to remember in this section of
control mode setting, but it is not difficult. It is mainly divided into five steps, namely:
1. You can view the current manual and automatic status according to the controller display screen.
2. If you want to adjust the control method, you need to click the "Startup Method" key to change the manual state of the controller between allow and prohibit.
3. If you set a password, you need to enter the password and then click the "Confirm key".
4. When setting the startup mode, click the "up and down keys" to adjust, and then click the "Confirm" key.
5. If the controller's automatic state is switched before the three states: non-allow, partial automatic and all automatic, you need to click the "TAB" key, then press the "up and down" key to change, and then click the "Confirm" key to return to the main interface.
Bus control Fire fighting linkage equipment is also called manual control. The corresponding fire fighting facilities can be started by manually operating the bus control panel.
1. Set the controller to be in the manual allowable working mode.
2. As in the above control method settings, first press "Startup Method", enter the password if you have a password, and press the "Confirm" key directly if you don't have a password, and then adjust it through the "up and down keys". It is best to press the "Confirm" key.
3. When the "Start" light is on for the first time, the "Feedback" light will also be on. This is start. When pressing again, cancel the command, the light goes out, and stop.
or above are all contents of the second section of Chapter 2. The exam will be assessed in the form of "manual operation + oral statement". This part of the content accounts for 12 points in the total score of the actual test, 5 points in the printer replacement, 3 points in the control mode setting, and 4 points in the bus control fire linkage setting.
Chapter 2 Section 3
Fire broadcast operation
Multi-line control panel operation
Identification of various types of html l5 Fire Detector
Chapter 2 Section 3 is divided into three parts, namely: fire broadcast operation, multi-line control panel operation, and identification of various fire detectors. The specific content is as follows:
1. Before using fire broadcast or fire telephone, it is necessary to confirm whether the controller is in a manually allowed state. If it is in a manually prohibited state, it will be switched to a manually allowed state through control.
2. Click the "Manual Method" key. If you have a password, enter the password. If you don’t have a password, press Confirm. After entering, use the "Up and Down" key to adjust. After adjusting to the manual allowable state, press the Confirm key.
3. After manual permission, we can use fire radio and telephone.
4. First, turn on the power switch of the broadcast power amplifier, the working order is on, the main light is on, and the volume can be adjusted at the same time.
5. Secondly, make broadcast selections, including emergency broadcast, microphone, mp3, etc. If you choose mp3, you need to plug it into the corresponding socket.
6. If you want to use a fire phone, you need to pick up the phone switchboard, enter the password with a password, but if you don’t have a password, confirm directly, press the corresponding extension selection key, and the corresponding extension rings. After the call is completed, the system will hang up and the system will return to the policy working state.
1. When we perform multi-wire control panel operation, we must first confirm whether it is in the allowable state. If it is in the prohibited state, twist the switch to the allowable state.
2. When it is adjusted to the allowable state, find the corresponding button to operate the facility, press the start button, the red indicator light is on, press the light again and then stop.
is relatively simple to identify various fire detectors. It mainly evaluates smoke and temperature sensation fire detectors. Just remember it clearly.
Usually when you go to the exam, the examiner will take out a detector. You just need to tell if it is a smoke or a temperature feeling. It is relatively simple.
or above is the entire content of the third section of Chapter 2. The examination is still assessed in the form of "manual operation + oral description". This part of the content accounts for 12 points in the total score of the actual test, fire broadcast operations account for 5 points, multi-line control panel operations account for 3 points, and various fire detectors are identified.
OK! The above is the entire content of the second chapter of the Intermediate Fire Facilities Operator Practice Examination. The content of the second chapter is a little more difficult than the first chapter, but if you read it carefully, it will be difficult to absorb and master it.
In fact, the most important thing in the actual exam is to be careful. Don’t forget any small operation to avoid losing points. In addition, consumers with conditions should do it and use these fire protection facilities, so that the exam will definitely be passed.
Finally, I hope that consumers can recommend AV to friends in need. Next, AV will work hard to bring more benefits to everyone (such as government employment recruitment, offline school training, etc.), so that we can work together for a better life! Come on
! !
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-