Artificial turf football field
1.Construction preparation:
a.Law preparation: Check the quantity, color, model and quality of the lawn before leaving the warehouse, and prepare the lawn paving construction drawings layout.
b. Auxiliary material preparation: The required auxiliary materials are accepted at the construction site, including: quartz sand , special glue, tape, rubber particles, and fully prepared for construction to avoid unnecessary loss of work.
c. Tool preparation: All tools for laying the lawn are transported to the construction site in advance, including a sand laying machine. 20 grass cutting knives , 4 trolleys, 2 glue mixers, 20 special sand columns, 10 hard brushes, 1 engineering felt cloth, a set of measuring tools, etc.
d.People preparation: 5 paving workers went to the site to clean the site before the artificial lawn entered the site and prepared for construction.
e. Weather requirements: The minimum temperature during construction shall not be lower than 10℃.
2. Foundation acceptance:
a. Check whether the foundation density and flatness of the entire lawn site meet the requirements.
b. The foundation surface should be flat, dry, free of debris, and pollution-free
3. Line laying out the line Find the center point of the site and determine the exact location of each point and line on the site based on the center point. According to the on-site situation of the stadium, arrange the site markings, refer to the floor plan and renderings, and match artificial turf with different performance and thickness.
4. Lawn paving Move the artificial turf into the site and spread it horizontally, pushing it to one end in sequence from the longitudinal end. Professionals must use professional tools to lay artificial turf. After the finished materials arrive at the construction site, the construction personnel will cut them according to the requirements of the drawings. Each lawn joint is connected with a special interface belt or is sewn with a special machine to make the entire lawn connected into one. During installation, the air humidity should not be too high to avoid construction in rainy or foggy days.
cutting function line Cut off the white grass line outside the lawn and set aside for later use.
6. Lawn overlapping: Spread 2cm~3cm between each joint of green lawn, and use a grass cutter or paper cutter to make the lawns on both sides overlap as closely as possible.
7. Lawn assembly: Lay 20cm~30cm wide fiber cloth or non-woven fabric along the joints of the lawn. If it is wet with water, it needs to be dried for a while, then apply the special glue evenly on the fiber cloth , and then splice the lawns on both sides and stick them to the fiber cloth. If the gap at the splicing is large, you can cut it apart twice cm~5cm and stretch it to the interface to ensure a beautiful appearance.
8. Inlaying function line After the lawn is basically spliced, cut the positions of each functional line and point of the site with a paper cutter, take out the cut grass wire, put it in the fiber cloth, apply special glue, put it back to the original prepared white grass wire, and press it tight with glue. Drawing arcs in narrow areas such as corner kicks is more difficult. The entire corner ball area can be cut into small pieces and then put back to splicing pieces.
lawn completion review After the lawn is spliced, the broken part on the lawn needs to be opened with paper cutter , straighten the dock, cut off the overlapping part, and then glue it; the markings are designed and planned according to the rules of the venue competition. After the markings are laid, check whether the joint area is solid, and check whether the intersection angle and lines are flat.
Filled quartz sand
a. Filled quartz sand can only be laid after the artificial lawn and playground are installed.
b. When laying sand and washing, the construction area is divided into small areas below one square meter according to the concept of integral method, and then divided into 24 (±) 1kg/㎡ laying capacity filling.
c. It is necessary to check whether the sand flushing laying is flat and sufficient, and make up for the shortcomings as appropriate.
d. During the paving process, other impurities should be removed immediately to ensure quality.
e. Sand filling and on-site drying must be kept in place during paving so that the limes can be filled with fluid.
f. After laying the sand, you need to use a hard brush or light load to drag the heavy brush back and forth to lay the sand back and forth to make the sand fall completely dense.
fill rubber particles a. The rubber particles are filled according to the sand-pulling method.
12. Complete acceptance Clean the site, check the specific dimensions of the site, strictly check whether the lawn is firmly sticky, and treat the uneven layer of quartz sand and rubber particles, and then complete it.
Plastic runway/basketball court/tennis court/football court/floor paint_construction_price quotation-DaShang Industrial (Shenzhen) Co., Ltd. https://www.dssysz.com
