Now everything is popular in "set". Today I will share with you Jiuzhou Fengshen , chassis + power supply + radiator installation experience. The specific models are: Xuantong chassis, DQ750M-V3L gold medal full-mode power supply, Ice Cube 620 radiator (dark night).
[Specific hardware configuration, you can make a reference]
CPU: AMD R5-5600
Motherboard: ROG X570-E
Memory: Zhiqi DDR4-3200 Huanguang Ji
Hard disk: Kaixia RD20 1TB + Seagate 3TB
Graphics card: Yingchi RTX2070S HOF 10th anniversary
Supplement: ①U is a new entry. The Ryzen 5000 price is quite good recently, and there is no need to consider D5 memory, which is very cost-effective. The 5800X I used to have a very serious heat accumulation, and the 360 water-cooled oven can be 90 degrees. So I found R5 for testing, which is suitable for most people. Actually, these two games are almost the same.
② I originally wanted to test it on RTX3090, but the official recommendation is above 1000W. Considering that the double baking test will be performed later, this time it is equipped with a rated 750W, so be honest with the 2070S, which is also a non-public strengthening Hall of Fame. Then, it officially begins.
[Case: Jiuzhou Fengshen Xuantong]
This is a mid-tower chassis, which is most compatible with E-ATX motherboards. The chassis copper column is installed in the position of the ATX motherboard by default. If you have other board types (such as Matx), please adjust them yourself first.
chassis measurements are 475 x 230 x 471mm, and both length and width are sufficient. Compatible with 380mm long graphics card, compatible with 175mm height radiator, and the head and top are compatible with 360 cold-cooled gear. The height of the chassis is slightly shorter (reference: Cool MB520 MESH 498mm, Bone Gaying Warrior X5 486mm). However, it does not affect the installation of the cold exhaust fan, and the back hole will not be blocked by the motherboard.
continues the consistent advantages of Jiuzhou Fengshen’s own "graphics card holder". The bracket can not only be adjusted up and down, but also can be changed left and right to adapt to supporting 3 fans and dual fan graphics cards.
Back hole rubber ring will not fall.
chassis material consists of: alloy body frame + tempered glass side plate + ABS head decorative surface, 3 parts. The nose part is the "finishing touch" of the entire product.
It not only comes with a 120 light fan (supports ARGB and PWM), but it looks like a bright eye looking at you. Moreover, the nose is an indescribable 3D three-dimensional face. Compared with the many chassis that emphasize symmetry, this one is indeed unique. I think the shape of
also has a great "effect", that is, even if the head is installed with only 1 fan, it will look uncontradictory. The fan looks extremely large. Hahaha, is there any?
hard disk bracket, you can use 2 3.5 mechanical hard disks. The screws need to be removed and the bracket is installed, and there is no quick-install (shock-absorbing) bracket.
Top magnetic dustproof net.
magnetic suction type, tempered glass side plate. The screwless design is designed with enough suction and needs to be buckled vigorously.
[Radiosink: Jiuzhou Fengshen Ice Cube 620 (black)]
Related supplements: If you search for this model, some will display AK620, it is Ice Cube 620. I also asked the customer service and said that I thought the Chinese logo was easier to remember, so the products before and after were "installed" with Chinese names, such as: Ice Cube 620, Illusion 560, Rubik's Cube 370, etc.
Ice Cube 620 points 3 versions: black and white, coated, it is expensive! Mainly used for matching some theme chassis. Another type is metallic (cheaper) and has the same performance.
Jiuzhou Fengshen, the logo has been changed once in the middle. The old version writes DeepCool text, and the new version is the pure graphic logo. Accessories include: buckle, silicon grease , screwdriver, and connecting wire.
basic parameters are as follows:
①6 pure copper heat pipes, heat dissipation power consumption is 260W;
② The base adopts pure copper + nickel plating process, with outstanding oxidation resistance;
③ double tower design. 600 fins, folded Fin + folded edge Fin, the end of the fin is wavy, which looks very good;
④Double 120mm FDB bearing silent fan. The fan speed is in the range of 500~1850RPM. Fan four-cornered rubber to reduce vibration;
⑤ Ice cube with a roof design, which is a way to increase appearance. Dense mesh shape, carefully touched during installation, easy to stuff grey.
installation experience, as follows:
debits are divided into intel (115X, 1200, 1700, 20XX), AMD AM4 platform. The page is even marked with Intel 13th generation and AM5 (Ryzen 7000). Intel's 13th generation buckle is the same as the 12th generation, and it will not be replaced, so there is no problem. Ryzen 7000, we haven't used it.
This time I installed the platform is AM4, using the backplane that comes with the motherboard. If it is intel platform , use the back panel that is standard in the buckle.
Installation steps: ① Use "space screws" to fix the back plate; ② Use "hand-tightening screws" to fix the bracket ; ③ Connect the bracket by the radiator.
vest strips can barely fit. I used the Zhi Fantasy Light Sphur, leaving only a little gap.
Some higher vest strips can only be adjusted. Refer to the picture above.
This radiator has no lights and is relatively simple to connect. It is to use the "Y" line to "summarize" the PWMs of the two fans, and then plug it into the CPU_FAN of the motherboard.
In order to improve the "front and rear air duct", I added an additional fan to the "Chrysanthemum" in the chassis.
[Power power supply: Jiuzhou Fengshen DQ750M-V3L gold medal full-mode power supply]
This model has obtained the 0PLUS gold medal certification and can be used with confidence. Gold medal certification requires that the power supply has a conversion rate of more than 87% when it is light load and full load; when it is 50% typical load, it must reach 90%; and when it is 100% load, it must reach 87%. The conversion rate of rubber bronze medals and silver medals is lower than that of gold medals. The higher the conversion rate, the higher the efficiency and the more power is. More importantly, the more you can ensure sufficient power supply.
motherboard power supply: 24Pin;
CPU power supply: 8Pin, (4+4)Pin;
Graphics card power supply (PCI-E): (6+2) Pin * 3;
Sata power supply: 4 ports * 2;
Pata power supply (large 4Pin): 4 ports * 4 ports * 1
full module power cord, increase or decrease according to your needs. If you don't need it, don't need to plug it in, saving installation space. PCI-E graphics card cable, each 8Pin has a single cable, making it more secure.
Other parameters: LLC + DC to DC architecture, all-day system capacitor , active PFC inductor. The fan supports intelligent start and stop, and the fan uses FDB bearings. With multiple circuit protection, if we encounter short circuits, error connections, etc., we will protect our computers from being "taken away in one wave".
[Test: Single and Double Griller]
Griller serves as a test for verifying power stability, and also serves as an overall cooling test for the "set" of Jiuzhou Fengshen. All hardware is at the default frequency, without any overclocking and PBO. The test ambient temperature is 21~22℃. The test process shall be based on the front, back, left and right side panels. A 120 fan is added to the rear of the chassis.
First of all, the results of single baking FPU
Single baking 15 minutes, core temperature 65 degrees, voltage 1.12V, CPU main frequency 4.22Ghz, power consumption 75W, fan speed 1100RPM.
Then, double bake.That is, single baking FPU + donut
single baking for 15 minutes, core temperature 70℃, voltage 1.104V, CPU main frequency 4.12Ghz, power consumption 75W, fan speed 1300. graphics card core temperature is also 70℃, and the graphics card fan speed is 1800. chassis fan 300RPM.
Comment: Two-time oven, CPU power consumption is stable at 75W. This shows that the cooling of Ice Cube 620 and the front and rear air ducts of the dazzling pupils have a reasonable design, which has achieved results. Let R5-5600 be stable at a level above TDP 10W. The maximum temperature is only 70 degrees. The noise of the whole machine is about 50 decibels, and it means a slight sound when placed on the desktop.
CPU is fully loaded at 75W and the graphics card is fully loaded at 251W. Generally, if I have this configuration, it is definitely enough to use 650W for a full configuration. Jiuzhou Fengshen 750W can leave room for future upgrades to RTX3070.
[Test: Large 3A Game]
If you like to play games, you can learn from this part. The performance of RTX2070S is stronger than that of RTX3060. I recorded the frame count and other related content in the game as follows.
"Horizon 5": Average 71 frames. 2K, extreme picture quality. CPU 53℃, usage rate 52%, power consumption 56W; GPU 64℃, usage rate 98%, power consumption about 180W.
" Assassin's Creed-Odyssey ": Average 58 frames. 2K, extremely high picture quality. CPU 57℃, usage rate 51%, power consumption 53W; GPU 62℃, usage rate 96%, power consumption about 180W.
"Need for Speed - Repayment": There is no benchmark test, just take a look in the game, the average frame is more than 100. 2K resolution, extremely high image quality.
"Tomb Raider-Shadow": Average 93 frames. 2K, the highest image quality. CPU 48℃, usage rate 29%, power consumption 41W; GPU 60℃, usage rate 97%, power consumption about 200W.
Through the above 4 games, everyone should have a relatively three-dimensional understanding of the performance, heat dissipation and power consumption of this configuration. Large 3A game, the load is much smaller than when the roaster was tested. The power consumption does not require full load and the temperature is very low. Can be used with confidence.
Summary:
After repeated testing, Jiuzhou Fengshen Ice Cube 620 double tower, pressing AMD R5-5600 (6 cores and 12 threads) has no problem at all. The oven temperature is 70℃ and the fan speed is only more than 1,000 points. Friends who like quietness can try it. The characteristic of the Xuantong chassis is the 3D shape of the machine head + the ARGB lamp fan, which has the thermal dissipation performance of the front and rear air ducts and rear. Finally, there is the DQ750M-V3L gold medal full-mode power supply, which is only 150mm long and has good installation compatibility. Suitable for use with R7-5800X+RTX3080 and below configurations. It is also equipped with multiple power supplies to prevent one wave from taking away.
